Integra DTR-9.1 appendix Default settings, Speaker Setup, Input Setup, Preference, Zone2 OSD Setup

Page 71

The default settings

The following table shows the factory-set default pa- rameter values. Use it as a reference when you change these parameter values as needed, although they are usable in many cases.

To return to the factory-set default parameters, press and hold down the VIDEO 1 button, and then press the STANDBY/ON button. “Clear” appears in the display and then the DTR-9.1 returns to the standby state.

1.Speaker Setup

1-1. Speaker Config

a. Subwoofer:

Yes

b. Front:

Small

c. Center:

Small

d. Surround L/R:

Small

e. Surround Back:

Small

1-2. Speaker Distance

a. Unit:

feet

b. Front L/R:

3.6m/12ft

c. Center:

3.6m/12ft

d. Surr Right:

2.1m/7ft

e. Surr Bk R:

2.1m/7ft

f. Surr Bk L:

2.1m/7ft

g. Surr Left:

2.1m/7ft

h. Subwoofer:

3.6m/12ft

1-3. Level Calibration

a. Left:

0.0dB

b. Center:

0.0dB

c. right:

0.0dB

d. Surr Right:

0.0dB

e. Surr Bk R:

0.0dB

f. Surr Bk L:

0.0dB

g. Surr Left:

0.0dB

h. Subwoofer:

0.0dB

VIDEO1: VIDEO1

VIDEO2: VIDEO2

VIDEO3: VIDEO3

VIDEO4: VIDEO4

VIDEO5: VIDEO5

b. Component Video: DVD: Component Video1

 

VIDEO1: ----

 

VIDEO2: Component Video2

 

VIDEO3: Component Video3

 

VIDEO4: ----

 

VIDEO5: ----

2-4. Listening Mode Setup

a. Analog/PCM:

Stereo

b. PCM fs>48k:

Stereo

c. PCM fs=192k:

Stereo

d. Dolby D:

Dolby D

e. DTS:

DTS

f. MPEG:

MPEG Multi

g. D.F.2ch:

Pro Logic

h. D.F.Mono:

Mono

2-5. Delay

a. A/V Sync:

0.0ms

b. Relative Delay Center:

0.0ms

c. Relative Delay Surr L/R:

0.0ms

d. Relative Delay Surr Back: 0.0ms 2-6. Sound Effect

a. Bass:

0

b. Treble:

0

2-7. Character Input

a. Character Display:

No

b. Character:

None

2-8. Miscellaneous Setup

a. IntelliVolume:

0dB

b. 12V Trigger:

Off

1-4. Bass Peak Level

a. Bass Peak Level Limiter: Off

b. Peak Level:

+18dB

1-5. LFE Level Setup

a. Dolby Digital:

0dB

b. DTS Cinema:

0dB

c. DTS Music:

0dB

d. MPEG Cinema:

0dB

e. MPEG Music:

0dB

2.Input Setup

2-1. Digital Setup

a. Digital Input:

CD: COAX1

 

TAPE1: OPT1

 

TAPE2: OPT2

 

DVD: OPT3

 

VIDEO1: ----

 

VIDEO2: COAX2

 

VIDEO3: COAX3

 

VIDEO4: COAX4

 

VIDEO5: COAX5

b. Digital Format:

Auto

2-2. Multichannel Setup

a. Multichannel:

CD: No

 

TAPE1: No

 

TAPE2: No

 

DVD: No

 

VIDEO1: No

 

VIDEO2: No

 

VIDEO3: No

 

VIDEO4: No

 

VIDEO5: No

2-3. Video Setup

a. Video:

CD: Last valid

 

PHONO: Last valid

 

FM: Last valid

 

AM: Last valid

 

TAPE1: Last valid

 

TAPE2: Last valid

 

DVD: DVD

4. Preference

4-1. Volume Setup

a. Volume Display:

Absolute

b. Muting Level:

- dB

c. Maximum Volume:

Off

d. Power On Volume:

Last valid

4-2. OSD Setup

a. Background Color:

Blue1

b. Superimpose Mode:

Normal

c. Immediate Display:

On

d. Display Position:

Bottom

e. Timeout:

3sec

f. TV Format:

Auto

4-3. OSD Tweak

a. ← / → / ↑ / ↓:

0.0

5.Zone2 OSD Setup

5-1. OSD Setup

a. Background Color:

Blue1

b. Superimpose Mode:

Normal

c. Immediate Display:

Off

d. Display Position:

Bottom

e. Timeout:

3sec

f. TV Format:

Auto

6. About

6-1. Lock Setup

a. Lock:

Unlocked

6-2.Version

b. Master ID:

_____________________

71

Page 70 Page 72
Image 71
Page 70 Page 72
Contents DTR-9.1 Avis Important SafeguardsModele pour les Canadien PrecautionsFor U.S. model For Canadian modelContents Contents Supplied accessoriesTHX Ultra FeaturesAssignable and Configuaragble 12-Volt Trig Using the remote controller Before using remote controllerFront panel display Front panel facilitiesFront panel Front panel doorFront panel facilities Off TuningPreset FM ModeSEND/LEARN indicator LCD display Power ON/STNBY button Remote controllerModel NO. DTR-9.1 Rear panel facilitiesCoaxial, optical, and input-only AC-3RF Rear panel facilitiesAC Inlet Video IN/OUT Video Monitor OUT Example of how to connect your equipmentStandard connections Example of how to connect your equipmentDefault setting Connecting a compact disc player Connecting your audio componentsConnecting a turntable Connecting an MD recorder, DAT deck, or CD recorderConnecting a television monitor or projector Connecting a LD playerConnecting a video cassette recorder Connecting a satellite tuner or televisionSpeaker placement Connecting speakersIdeal speaker configuration Minimum speaker configuration for surround sound playbackConnecting a subwoofer Connecting speakersAssembling the AM loop antenna Connecting antennasConnecting the AM loop antenna Directional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaOutline Connecting to the IR in Zone 2 inputConnecting the main and remote zones Cabinet Connecting to the IR in Main inputRemove the jumper plugs Connect a graphic equalizer Connecting a graphic equalizer Connecting power amplifiersRemove the jumper plugs Connect the power amplifiers Turning the power on from the remote controller Connecting the powerOSD menu consists of a main screen that is divided Up into six menus Speaker Setup, Input Setup, ListeningOn-Screen Display OSD menu Your home theater, and it rarely needs to be Changed laterPress the Menu button On-Screen Display OSD menuNavigating through the OSD menu Speaker Config sub-menu Speaker SetupSpeaker Distance sub-menu Speaker SetupCalibrating the speaker levels Level Calibration sub-menuBass Peak Level Bass Peak Level Manager* sub-menu LFE Level Setup sub-menuDigital Setup sub-menu Input SetupInput Setup Video Setup sub-menu Multichannel Setup sub-menuDTS Mpeg Listening Mode Preset sub-menuListening Modes Input source signalsInput Setup 123456789012345678901234 4.Preference Delay sub-menu Sound Effect sub-menuCharacter Input sub-menu Miscellaneous SetupListening Mode Setup menu Listening Mode SetupListening Mode Setup Description listening mode parameters THX Preference Volume Setup sub-menuOSD Tweak OSD Setup sub-menuPreference Version Zone2 OSD SetupLock Setup sub-menu AboutInput selector buttons Power VOLEnjoying music or videos in the remote zone Press the Zone 2 button on the DTR-9.1 Select a sourceListening to FM/AM Radio Stations PresetListening to Radio Broadcasts Press the Memory button on the front panel Press the Enter button again to finalize the procedureThis erases the selected preset station Listening to Radio BroadcastsUsing the many features of the DTR-9.1 Changing the listening modeSelecting an input source Listening with headphones Adjusting the volumeEnjoying the multichannel output Enjoying music or videos with the DTR-9.1If one of the messages shown below appears Start recording at the recording component as desired Recording a sourcePress the Rec Out button twice within 8 seconds Recording a source Controlling the DTR-9.1 Using remote controllerUsing the remote controller to control each device Press the AUDIO/TAPE Mode buttonListening mode buttons Using remote controllerControlling an Integra MD recorder Press the CD Mode buttonPress the MD Mode button Controlling an Integra CD playerPress the TUN input selector button Controlling an Integra cassette tape deckControlling an Integra DVD player Press the DVD Mode buttonSAT, CABLE, VCR, and TV Mode buttons Buttons Programming procedurePage You can only erase memorized commands and not preset ones Erasing the programmed command from one buttonPress and release the same Mode button again SEND/LEARN indicator Mode buttonsRunning a Macro function Using a Macro functionPress the Mode Macro button to complete the programming Programming a Macro functionCheck to see if the macro has been properly programmed Using a Macro functionPress the Direct Macro button to complete the procedure Programming the Direct Macro functionPress the Direct Macro button again Press the Mode Macro button againOperation Erasing all commands and macros that have been programmedMacro mode programming memo Press the ENT buttonTroubleshooting guide Troubleshooting guide LFE Level function cannot be used OSD menu settings cannot be changedCannot change OSD Menu settings Late Night function cannot be usedZone2 OSD Setup Default settingsSpeaker Setup Input SetupInputs Your system settingTape Your system settingSpeakers OSD SetupMode Remote controllerSpecifications Other upgraded function Upgraded-2 Important points regarding speaker placement Speaker configuration and placement/ Connecting speakersCrossover80HzTHX QuitOSD Boundary Gain Channel digital surround format Digital Setup sub-menu Listening Mode Preset sub-menuRelationship between input source and listening mode Upgraded-8 THX When Upsampling is set to On, DTS Neo6 cannot be selected DTS-ES Upgraded-12 DTS-ES Upgraded-14 Parameter Delay sub-menu Other upgraded function

DTR-9.1 specifications

The Integra DTR-9.1 is a high-performance 7.1-channel surround sound receiver designed for audiophiles and home theater enthusiasts who demand superior sound quality and advanced features. This model, crafted by the renowned manufacturer Integra, showcases a blend of cutting-edge technology and user-friendly operation, making it a standout choice for home entertainment systems.

One of the notable features of the DTR-9.1 is its robust amplification system. Equipped with discrete high-current amplifiers, it delivers a powerful output of 130 watts per channel, ensuring dynamic sound reproduction for movies, music, and gaming. The receiver supports various surround sound formats, including Dolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio, and DTS Neo:6, providing an immersive audio experience that brings your media to life.

The DTR-9.1 incorporates advanced video processing capabilities, including upscaling of standard definition and high definition content to 1080p via HDMI, ensuring that your visuals maintain clarity and detail. With multiple HDMI inputs and outputs, this receiver offers extensive connectivity options, accommodating various devices such as Blu-ray players, gaming consoles, and streaming devices.

Another significant aspect of the Integra DTR-9.1 is its integration of Audyssey technologies, specifically Audyssey MultEQ and Audyssey DynamicEQ. These features enable automatic room calibration, optimizing speaker settings to adapt to the acoustic characteristics of your space. This ensures balanced sound reproduction across all frequencies, providing an enhanced listening environment.

In addition, the DTR-9.1 is equipped with a user-friendly interface and an ergonomic remote control, offering ease of navigation through its features. The on-screen display is intuitive, making it accessible for users to adjust settings and preferences with minimal hassle.

For music enthusiasts, the receiver supports streaming services and includes built-in Bluetooth and Wi-Fi connectivity, allowing for seamless streaming from smartphones or tablets. The DTR-9.1 also features a Zone 2 output, enabling multi-room audio setups, delivering flexibility in how and where to enjoy your favorite tunes.

Overall, the Integra DTR-9.1 combines exceptional sound quality, versatile connectivity, and advanced technologies, making it a top choice for consumers looking to enhance their home audio and video experience. Whether used for thrilling movie nights or casual music listening, this receiver promises to deliver performance and satisfaction for discerning users.
Top Page Image Contents