Integra ST2 instruction manual Update Firmware Chassis cont’d, Factory Initialization Chassis

Page 22

ST2 TUNER PROGRAMMING

ST2 TUNER SETUP MENU

Press and Hold TNR SEL button

ST2 Chassis Setup Procedures

TNR TNR

SEL SEL

TUNER

SOURCE

UPDATE

FACTORY

SYSTEM

Chassis

SETUP

NUM

FIRMW

INIT

 

INFO

Setup

Menu

Procedure

Procedure

Procedure

Procedure

Menu

 

 

 

TNR

 

 

 

 

 

 

SEL

 

 

 

 

 

 

 

 

This

 

 

 

 

TUNER

HOLD

Procedure

 

 

 

#

BAND

returns the

 

 

 

 

 

ST2 Tuner

 

 

 

 

 

to its

 

 

 

 

 

 

Factory

 

 

 

 

 

settings

 

 

 

 

After update

 

 

 

 

 

 

cycle Power

 

 

 

 

 

SOURCE

 

Are you sure

 

 

 

NUM

Start

 

 

 

 

 

 

 

 

 

 

 

 

Update

 

 

 

 

 

 

 

YES

NO

 

 

 

 

Cycle Power

Please wait

 

 

 

 

 

 

 

 

 

 

Cycle Power

 

 

Update Firmware (Chassis) (cont’d)

4.“Hold BAND” appears on the tuner.

5.While pressing and holding BAND, “After update cycle power” appears on the tuner display.

6.When “Start Update” appears on the tuner dis- play, start the update program. “Finished” appears on the computer screen when complete.

7.Cycle power to the tuner.

Factory Initialization (Chassis)

The Factory Initialization procedure allows the erasure of all programmed settings and returns them to the factory default settings.

1.Enter the Setup Menu by pressing and holding the TNR SEL button.

2.TUNER SETUP appears. Press MEM Up/Down until FACTORY INIT appears on the tuner.

3.Press BAND to enter the FACTORY INIT menu.

4.“Are you sure” appears on the tuner. Using the Tune Up/Down buttons, view the “Yes” and “No” selections.

5.Press BAND to select. A “No” selection

returns to the top of the Factory Init menu. A “Yes” begins the initialization.

6.“Please wait” appears on the tuner during the process and “Cycle Power” appears when com- plete.

7.Cycle power on the ST2 tuner.

22

Image 22
Contents ST2 Smart Tuner Important Safeguards Safety InstructionsTable of Contents RNET-enabled System IntroductionBOX Contents Component Guide ST2 Front PanelST2 Rear Panel ST2 S mart TunerST2-RC Remote Control ST2 Setup and Connections Basic ConnectionsST2-KP Connections to ST2 Tuner Non-RNET Systems ST2-KP and CAV6.6 ConnectionsSource Connections with CAV6.6 Controller/Amplifier Source Connections with CAi Series Controller/Amplifier Source Connections with A-BUS Audio Distribution HubAM Antenna Connecting an Indoor and Outdoor AntennaAntenna Connections FM AntennaGrounding an Outdoor Antenna Front Panel Controls ST2 OperationFront Panel Operation Frequency Seek ST2-RC Remote Control OperationSaving Favorites ST2-KP Keypad Controls ST2-KP Keypad OperationFrequency Scan UNO-S2 Keypad Controls with CAV6.6CAV6.6-UNO-S2 Keypad Operation MuteMHz FM UNO-LRC1 Remote Control with CAV6.6 UNO-LRC1 Remote Control OperationSeek UP/DOWN Seeks next tuned station up or down ST2 Chassis Setup Menu ST2 Tuner Setup MenuST2 Tuner Programming Update Firmware Chassis cont’d Factory Initialization ChassisMemory Name AM/FM Tuner Setup Menu for AM/FMSystem Info Chassis Bank Name AM/FMBank Name AM/FM cont’d Backup and RestoreRegion AM/FM Source Configuration Note Programming for CAV6.6 USETechnical Specification ST2 Smart TunerWarranty & Repair Russound Rev 5/24/04 28-1150