Integra ST2 instruction manual Bank Name AM/FM cont’d, Region AM/FM, Backup and Restore

Page 24

ST2 TUNER PROGRAMMING

ST2 TUNER SETUP MENU

Bank Name (AM/FM) (cont’d)

14.Press BAND to save bank name. The Bank Name menu returns to the Tuner # prompt to name other banks, or press TNR SEL to exit the Bank Name menu.

Region (AM/FM)

The Region procedure assigns either US or Euro to the tuner. The difference between the two is that US FM frequencies operate in .2 MHz incre- ments, while European FM frequencies operate in

.05 MHz increments.

(END OF AM/FM TUNER SETUP)

Backup and Restore

Once all of the tuner settings are completed, it may be advisable to create a backup of the pro- grammed settings for future use. The backup will then be available in case tuner settings need to be restored.The backup and restore PC applica- tion “RNET Backup” is available through the Document Center at www.russound.com. Also required are a DB9 male-to-female cable and lap- top or desktop PC.

Press TNR SEL

button to select

AM/FM Tuner

AM/FM Setup Menu

TNR TNR

SEL SEL

TUNER

SOURCE

UPDATE

FACTORY

SYSTEM

Chassis

SETUP

NUM

FIRMW

INIT

INFO

Setup

Menu

Procedure

Procedure

Procedure

Procedure

Menu

TNR

 

 

 

 

 

 

SEL

 

 

 

 

 

 

MEM

 

 

BANK

 

REGION

AM/FM

NAME

 

 

NAME

 

Procedure

Setup

Procedure

 

 

Procedure

 

 

Menu

TNR

 

 

 

 

 

 

SEL

 

 

 

 

 

 

 

 

 

TNR

 

 

 

 

 

 

SEL

 

 

 

BANK #

MEMORY #

MEMORY

 

 

 

 

NAME

 

 

 

 

 

 

 

 

 

 

 

 

 

BANK #

BANK

SAVE

 

 

 

 

NAME

CHANGES?

 

 

 

 

 

 

 

 

Selects

 

 

 

 

 

 

character

 

 

 

 

 

 

 

 

Selects

 

 

 

 

Selects

 

character

 

 

 

 

 

 

 

 

 

 

character

 

 

 

 

 

 

position

 

 

 

 

 

 

Repeat

 

Selects

 

 

 

 

for each

 

character

 

 

 

 

character

 

position

 

 

 

 

in name

 

 

 

 

 

 

 

 

Repeat

 

 

 

 

 

 

for each

 

 

 

 

 

 

character

 

 

 

 

SAVE

 

in name

 

 

 

 

 

 

 

 

 

 

CHANGES?

 

 

 

 

24

Image 24
Contents ST2 Smart Tuner Important Safeguards Safety InstructionsTable of Contents RNET-enabled System IntroductionBOX Contents Component Guide ST2 Front PanelST2 Rear Panel ST2 S mart TunerST2-RC Remote Control ST2 Setup and Connections Basic ConnectionsST2-KP and CAV6.6 Connections ST2-KP Connections to ST2 Tuner Non-RNET SystemsSource Connections with CAV6.6 Controller/Amplifier Source Connections with CAi Series Controller/Amplifier Source Connections with A-BUS Audio Distribution HubConnecting an Indoor and Outdoor Antenna Antenna ConnectionsAM Antenna FM AntennaGrounding an Outdoor Antenna ST2 Operation Front Panel ControlsFront Panel Operation ST2-RC Remote Control Operation Frequency SeekSaving Favorites ST2-KP Keypad Controls ST2-KP Keypad OperationUNO-S2 Keypad Controls with CAV6.6 CAV6.6-UNO-S2 Keypad OperationFrequency Scan MuteMHz FM UNO-LRC1 Remote Control with CAV6.6 UNO-LRC1 Remote Control OperationSeek UP/DOWN Seeks next tuned station up or down ST2 Tuner Setup Menu ST2 Chassis Setup MenuST2 Tuner Programming Update Firmware Chassis cont’d Factory Initialization ChassisTuner Setup Menu for AM/FM System Info ChassisMemory Name AM/FM Bank Name AM/FMBackup and Restore Bank Name AM/FM cont’dRegion AM/FM Source Configuration Note Programming for CAV6.6 USETechnical Specification ST2 Smart TunerWarranty & Repair Russound Rev 5/24/04 28-1150