Integra ST2 instruction manual Programming for CAV6.6 USE, Source Configuration Note

Page 25

ST2 TUNER PROGRAMMING

PROGRAMMING FOR CAV6.6 USE

NOTE: The CAV6.6 firmware must be version 2.00.01 or higher and UNO-S2 firmware must be version 3.00.01 or higher to control the ST2 Tuner. Use the System Info Menu of the CAV6.6 to check the firmware version. If the firmware is not the proper revision as noted here, visit the Document Center at www.russound.com to obtain the latest version.

To Program the CAV6.6 to operate with the ST2 Tuner: (refer to the CAV6.6 Instruction Manual for details)

1.Enter the Setup Menu by pressing the Setup button on the side of the UNO-S2 keypad.

2.SOURCE SETUP will appear. Enter the Source Setup Menu by pressing the Play button on the UNO-S2 keypad.

3.BASIC SETUP will appear. Enter the Basic Setup Menu by pressing the Play button again.

4.SOURCE NUM will appear. Use + and - buttons to select the source number to which Tuner 1 is connected. Press the Play button to enter your choice.

5.SOURCE NAME will appear. Use + and - buttons to select the name for the source (e.g., Tuner 1). Press the Play button to enter your choice.

6.COMMAND TYPE will appear. Select PERIPHERAL from the list. Press the Play button to enter this choice.

7.SAVE CHANGES? appears. Select “Yes” and press the Play button to save changes.

8.SOURCE NUM appears again. Repeat steps 4 through 7 to configure the second tuner.

9.Press the Setup button three times to back out of the Installation Menu.

Source Configuration Note:

When the ST2 Tuner is used with the CAV6.6 or other RNET controller, it is configured as an RNET command type “Peripheral” and is connected via the RNET bus. This makes the tuner behave as a fully integrated device with UNO-S2 keypad support. Each tuner must be set up with a unique source number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus.

Key Function Note: When using the tuner with the CAV6.6-S2 system, do not reassign keypad and remote buttons for tuner control in the CAV6.6 Key Configuration Menu. When the tuner is assigned the “Peripheral” command type in the CAV6.6 Setup Menu, key assignments and functions are auto- matically assigned and will operate as shown in the preceding UNO-S2 keypad and UNO-LRC1 remote diagrams.

25

Image 25
Contents ST2 Smart Tuner Safety Instructions Important SafeguardsTable of Contents Introduction RNET-enabled SystemBOX Contents ST2 Front Panel Component GuideST2 S mart Tuner ST2 Rear PanelST2-RC Remote Control Basic Connections ST2 Setup and ConnectionsST2-KP Connections to ST2 Tuner Non-RNET Systems ST2-KP and CAV6.6 ConnectionsSource Connections with CAV6.6 Controller/Amplifier Source Connections with A-BUS Audio Distribution Hub Source Connections with CAi Series Controller/AmplifierAntenna Connections Connecting an Indoor and Outdoor AntennaAM Antenna FM AntennaGrounding an Outdoor Antenna Front Panel Controls ST2 OperationFront Panel Operation Frequency Seek ST2-RC Remote Control OperationSaving Favorites ST2-KP Keypad Operation ST2-KP Keypad ControlsCAV6.6-UNO-S2 Keypad Operation UNO-S2 Keypad Controls with CAV6.6Frequency Scan MuteMHz FM UNO-LRC1 Remote Control Operation UNO-LRC1 Remote Control with CAV6.6Seek UP/DOWN Seeks next tuned station up or down ST2 Chassis Setup Menu ST2 Tuner Setup MenuST2 Tuner Programming Factory Initialization Chassis Update Firmware Chassis cont’dSystem Info Chassis Tuner Setup Menu for AM/FMMemory Name AM/FM Bank Name AM/FMBank Name AM/FM cont’d Backup and RestoreRegion AM/FM Programming for CAV6.6 USE Source Configuration NoteST2 Smart Tuner Technical SpecificationWarranty & Repair Russound Rev 5/24/04 28-1150