Integra ST2 instruction manual BOX Contents

Page 5

INTRODUCTION

IR-controlled System

CAi Series -

The ST2 Tuner can be controlled by infrared commands received through the two IR connec- tions on the rear panel. The ST2 contains two individual tuners, which makes it act as two sources in the CAi system. There are two source audio outputs and two IR connections - one for each tuner in the ST2. You will need at least one IR link cable (Russound P/N 09-0508) for these connections (one is supplied with each CAi sys- tem). There are two unique IR code sets for Tuner 1 and Tuner 2, which allow each to be con- trolled independently from either IR connection. These codes can be learned from the ST2-RC remote control into the CA-LRC1 remote control and/or the DSC and DAN IR learning keypads. If you are using an IR-controlled system from anoth- er manufacturer, installation should be similar. The ST2 IR codes may be learned into many other manufacturers’ remote controls that have learning capability for unified control over the A/V equipment.

A-BUS®System -

The ST2 Tuner can be used in an A-BUS system with an audio distribution hub such as the A-H484 and IR-repeating keypads such as the A-KP2. The connections on the rear panel are designed to receive IR signals from a repeating system commonly used in A-BUS distributed audio systems.

For A-BUS applications, as with the CAi series installation, the two tuners in the ST2 unit must be set up as two sources, with two source audio inputs and two IR connections. You will need two IR link cables for these connections. The two IR code sets can be learned from the ST2-RC remote into the A-LRC1 remote control.

Note: Optional ST2-KP keypads can be used to provide control for the ST2 Tuner and are designed to be used with IR-controlled systems.

RS-232 Controlled System

The ST2 Tuner can be controlled using the RNET protocol provided via the RS-232 port on the rear panel. It can also be controlled by any RS-232-enabled control system (e.g., Crestron, AMX). Information on RS-232 operation is avail- able to dealers on the Russound web site, www.russound.com.

BOX CONTENTS

The ST2 Tuner comes with the parts needed to setup and operate the component. These include:

ST2 Tuner (two AM/FM modules)

ST2-RC remote control

12VDC power supply

AM loop antenna (2)

FM antenna (2)

RCA audio cable (2)

Rack mount ears

If any of these parts are missing, please call Russound at 800-638-8055 ext. 501 for assistance.

5

Image 5
Contents ST2 Smart Tuner Safety Instructions Important SafeguardsTable of Contents Introduction RNET-enabled SystemBOX Contents ST2 Front Panel Component GuideST2 S mart Tuner ST2 Rear PanelST2-RC Remote Control Basic Connections ST2 Setup and ConnectionsSource Connections with CAV6.6 Controller/Amplifier ST2-KP and CAV6.6 ConnectionsST2-KP Connections to ST2 Tuner Non-RNET Systems Source Connections with A-BUS Audio Distribution Hub Source Connections with CAi Series Controller/AmplifierAntenna Connections Connecting an Indoor and Outdoor AntennaAM Antenna FM AntennaGrounding an Outdoor Antenna Front Panel Operation ST2 OperationFront Panel Controls Saving Favorites ST2-RC Remote Control OperationFrequency Seek ST2-KP Keypad Operation ST2-KP Keypad ControlsCAV6.6-UNO-S2 Keypad Operation UNO-S2 Keypad Controls with CAV6.6Frequency Scan MuteMHz FM UNO-LRC1 Remote Control Operation UNO-LRC1 Remote Control with CAV6.6Seek UP/DOWN Seeks next tuned station up or down ST2 Tuner Programming ST2 Tuner Setup MenuST2 Chassis Setup Menu Factory Initialization Chassis Update Firmware Chassis cont’dSystem Info Chassis Tuner Setup Menu for AM/FMMemory Name AM/FM Bank Name AM/FMRegion AM/FM Backup and RestoreBank Name AM/FM cont’d Programming for CAV6.6 USE Source Configuration NoteST2 Smart Tuner Technical SpecificationWarranty & Repair Russound Rev 5/24/04 28-1150