ResMed Humidifier user manual Removing and Storing the Connector Plug, Attaching Your Humidaire

Page 11

Notes

•To replace the front cap, align it with your flow generator (B-4)and push it firmly until it clicks into place.

•Remember to take the front cap with you when travelling, in case you need CPAP therapy without a humidifier.

REMOVING AND STORING THE CONNECTOR PLUG

Please refer to the illustrations in section C of the illustration sheet.

Before attaching the HUMIDAIRE 3i, remove the connector plug from your flow generator (C-1)and attach it to the back of the docking station (C-2).

ATTACHING YOUR HUMIDAIRE 3i

Please refer to the illustrations in section D of the illustration sheet.

1Align your HUMIDAIRE 3i with your flow generator (D-1)and push them together until they click into place (D-2).

WARNING

! • The HumidAire 3i docking station should only be connected or disconnected when the water chamber is empty.

• Water must be prevented from entering your flow generator. Do not transport the flow generator with the HumidAire 3i attached.

2Insert the power cord into the socket at the rear of your flow generator. Plug the other end of the power cord into a power outlet (D-3).

Note: If your flow generator is powered via the DC input, the HumidAire 3i is not powered and humidification output will be reduced.

3Place the combined unit on a firm, level surface near your bed at a level lower than your sleeping position. Ensure the surface is not sensitive to heat and/or moisture, or use a protective mat.

!

4

CAUTION

Be careful not to place the unit where it can be bumped into and knocked over.

Connect one end of the air tubing firmly onto the air outlet of your HUMIDAIRE 3i and the other end to your mask (D-4).

FILLING THE WATER CHAMBER

Please refer to the illustrations in section E of the illustration sheet.

!

1

WARNING

Take care when handling your HumidAire 3i. The water and the water chamber base may both be hot. Allow ten minutes for the heater plate and any excess water to cool.

Release the cover latch (E-1)and lift the cover until it rests in the upright position (E-2).

6

Page 10 Page 12
Image 11
Page 10 Page 12
Contents HumidAire HumidAire 3iTM RE-ASSEMBLING Your Humidaire 3i / Sätta Ihop Humidaire 10 minHumidaire Manufactured by English Contents Your Responsibility What is the Humidaire 3i?Welcome Contraindications Medical InformationIntended USE Removing the Front CAP if Fitted Setting UP Your Humidaire 3i for USEComponents of Your Humidaire Filling the Water Chamber Removing and Storing the Connector PlugAttaching Your Humidaire Starting Your Treatment Starting and Stopping TreatmentDetaching Your Humidaire Stopping Your TreatmentRemove the water chamber from the docking station G-3 Frequently Asked QuestionsDisassembling Your Humidaire Cleaning and MaintenanceReassembling Your Humidaire Cleaning Your HumidaireServicing Problem Possible Cause Solution TroubleshootingWater leaves scaly IEC 60601-1 Classification Technical SpecificationsSymbols Which Appear on the Device Product Warranty Period Limited WarrantyPage Index FAQPage Bruksanvisning Innehåll Ditt Ansvar VälkommenVAD ÄR Humidaire 3i? Varningar Medicinsk InformationAvsedd Användning KontraindikationerSe illustrationerna i del B på illustrationsbladet Installera HumidaireDelar I Humidaire Se illustrationerna i del a på illustrationsbladetTA Bort OCH Förvara Kopplingskontakten Se illustrationerna i del C på illustrationsbladetSe illustrationerna i del D på illustrationsbladet Se illustrationerna i del E på illustrationsbladetStarta Behandlingen Starta OCH Avbryta BehandlingenSe illustrationen i del F på illustrationsbladet Ii. Efter 2 sekunder visas displaybilden Uppvärmning Avbryta Behandlingen Ofta Förekommande FrågorSe illustrationerna i del G på illustrationsbladet Obs! Sätt tillbaka kopplingskontakten i flödesgeneratornVAD GÖR JAG OM JAG Inte KAN FÅ Bukt MED Mina TORRHETSSYMTOM? TA Isär Humidaire Rengöring OCH UnderhållSe illustrationerna i del H på illustrationsbladet Sätta Ihop Humidaire Se illustrationerna i del I på illustrationsbladetRengöra Humidaire Service Felsökning Problem Möjlig orsak LösningFelsökning Tekniska Specifikationer Symboler PÅ Utrustningen Obs! Vissa modeller finns inte i alla omoråden Begränsad GarantiSakregister Page Brugermanual Indhold DIT Ansvar VelkommenHvad ER EN Humidaire 3i? Advarsler Medicinske OplysningerAnvendelse Se illustrationen i afsnit a på illustrationsarket Dele TIL HumidaireSe illustrationen i afsnit D på illustrationsarket Klargøring AF HumidaireSe illustrationen i afsnit B på illustrationsarket Se illustrationen i afsnit C på illustrationsarketOpfyldning AF Vandbeholder Indledning OG Standsning AF BehandlingenSe illustrationen i afsnit E på illustrationsarket Se illustrationen i afsnit F på illustrationsarketIi. Efter 2 sekunder vises skærmbilledet Opvarmer Afmontering AF Humidaire Se illustrationerne i afsnit G på illustrationsarketStandsning AF Behandlingen Se illustrationen i afsnit H på illustrationsarket Hyppigt Stillede SpørgsmålRengøring OG Vedligeholdelse Rengøring AF Humidaire Tag luftslangen af luftudtaget H-5Samling AF Humidaire Se illustrationerne i afsnit I på illustrationsarketFejlfinding Problem Mulig årsag LøsningSørg for, at dækslet er låst ordentligt fast Maksimal strøm på varmelegeme 85 W Tekniske SpecifikationerSymboler PÅ Apparatet Produkt Garantiperiode GarantiPage Indeks Page Brukerhåndbok Starte OG Stanse Behandling InnholdHVA ER Humidaire 3i? Medisinsk InformasjonLes nøye gjennom håndboken før du tar utstyret i bruk HVA ER Humidaire 3i?Kontraindikasjoner Medisinsk InformasjonTiltenkt Bruk Se illustrasjonene i figur a på illustrasjonsarket Komponentene I Humidaire 3i-apparatetSe illustrasjonene i figur D på illustrasjonsarket Slik Klargjør DU Humidaire 3i for BrukSe illustrasjonene i figur B på illustrasjonsarket Se illustrasjonene i figur C på illustrasjonsarketFylle Vannbeholderen Starte OG Stanse BehandlingSe illustrasjonene i figur E på illustrasjonsarket Se illustrasjonene i figur F på illustrasjonsarketIi. Etter 2 sekunder vises OPPVARMING-skjermen Frakobling AV Humidaire Vanlige SpørsmålSe illustrasjonene i figur G på illustrasjonsarket Stansing AV BehandlingenTrenger JEG Å Bruke Destillert Vann I VANNBEHOLDEREN? Demontering AV Humidaire Rengjøring OG VedlikeholdSe illustrasjonene i figur H på illustrasjonsarket Sette Sammen Humidaire 3i Igjen Se illustrasjonene i figur I på illustrasjonsarketRengjøring AV Humidaire Vedlikehold Feilsøking Problem Mulig årsak LøsningFeilsøking MÅL H X B X D Tekniske SpesifikasjonerSymboler SOM Vises PÅ Apparatet Page Merk Enkelte modeller er ikke tilgjengelige i alle land Begrenset GarantiPage Register Page Käyttöohje Sisällysluettelo Käyttäjän Vastuu TervetuloaMikä Humidaire 3i ON? Varoitukset Hoitoa Koskevat TiedotKäyttötarkoitus KontraindikaatiotKatso kuvasivun kohdassa a olevia kuvia Humidaire 3i -LAITTEEN OsatKatso kuvasivun kohdassa D olevia kuvia Humidaire 3i -LAITTEEN KäyttöönottoKatso kuvasivun kohdassa B olevia kuvia Katso kuvasivun kohdassa C olevia kuviaVesisäiliön Täyttäminen Hoidon Aloittaminen JA LopettaminenKatso kuvasivun kohdassa E olevia kuvia Katso kuvasivun kohdassa F olevia kuviaLämmitystoiminto EI Kaikissa Malleissa Humidaire 3i -ILMANKOSTUTTIMEN Irrottaminen Yleisimmin Esitettyjä KysymyksiäKatso kuvasivun kohdassa G olevia kuvia Hoidon LopettaminenMitä TEEN, JOS Kuivuudesta Johtuvat Oireet JATKUVAT? Humidaire 3i -ILMANKOSTUTTIMEN Purkaminen Puhdistus JA HuoltoKatso kuvasivun kohdassa H olevia kuvia Humidaire 3i -KOSTUTTIMEN Kokoaminen Katso kuvasivun kohdassa I olevia kuviaHumidaire 3i -KOSTUTTIMEN Puhdistaminen Huolto Ongelma Mahdollinen syy Ratkaisu Ongelmien SelvittäminenOngelmien Selvittäminen Lämmityslevyn maksimilämpötila 85 C Lämpötilakatkaisu 93 C Tekniset TiedotLaitteessa Käytetyt Symbolit 100 Tuote Takuuaika Huomautus Kaikkia malleja ei ole saatavissa kaikkialla102 Hakemisto 104

Humidifier specifications

The ResMed Humidifier is a cutting-edge device designed to enhance the comfort and efficacy of sleep therapy. It is particularly beneficial for individuals using Continuous Positive Airway Pressure (CPAP) therapy, as it helps to alleviate dry throat and nasal passages, common complaints associated with air pressure treatment. ResMed's advanced humidifiers are engineered with a focus on user comfort, adaptation, and seamless integration with various ResMed CPAP machines.

One of the standout features of the ResMed Humidifier is its integrated heating element. This technology ensures that the delivered air is warmed to a comfortable temperature, reducing the sensation of cold air entering the airways. The humidification process can be adjusted to meet individual preferences, offering customizable settings for optimal relief from dryness.

The ResMed Humidifier also incorporates Climate Control technology, a significant advancement that regulates temperature and humidity based on the ambient room conditions. This means that regardless of the external environment, users can experience consistent and comfortable humidification all night long. The automated adjustments eliminate the need for manual tweaks, as the device intelligently responds to changes in temperature and humidity levels, ensuring a consistent therapy experience.

Another important characteristic is the device's ease of use and minimal maintenance requirements. The water chamber is designed for simple filling and cleaning, often featuring a dishwasher-safe design that makes hygiene a breeze. This promotes not only better respiratory health but also longer equipment lifespan.

Additionally, the ResMed Humidifier often boasts a sleek, modern design that seamlessly blends with existing CPAP machines. Its intuitive interface allows users to navigate settings easily, ensuring that adjustments can be made quickly and without hassle.

Moreover, the device supports Bluetooth connectivity, enabling users to track therapy data through mobile applications. This connectivity facilitates better engagement with one's treatment, allowing for insights into usage patterns, compliance, and overall health monitoring.

In summary, the ResMed Humidifier is a sophisticated solution that enhances the comfort of CPAP therapy through its innovative features, including heating elements, Climate Control technology, user-friendly design, and connectivity options. These characteristics make it an essential tool for individuals seeking to improve their sleep quality and overall health while undergoing respiratory therapy. Its commitment to user comfort and advanced technological integration reflects ResMed's dedication to improving lives through innovative health solutions.
Top Page Image Contents