ResMed III user manual Treatment Screens, Treatment screen

Page 33

Treatment Screens

After starting treatment, you can display one of the treatment screens below. Press the Up/Down key to switch between views.

Ramping indicator

Treatment mode Trigger indicator

Set pressure(s)

}

S:RAMP 8.0–16.6

S>>>>> exit

}

Pressure bar graph

Figure 3: Treatment screen 1

Leak			LK: 24L/min			RR: 12		Respiratory rate


Minute			MV: 12.0			VT:1000		Tidal volume
ventilation

Figure 4: Treatment screen 2

Cycle indicator
(TiMn / C / TiMx)
(TiMn / C / TiMx)
Trigger indicator
				S ∗ ∗ C

Measured
				Ti 1.5s
				Ti 1.5s
inspiration time

Figure 5: Treatment screen 3

TiMx 2.0			Set IPAP Max


1:2.5			Measured I:E ratio

The treatment screens contain the following information:

Treatment mode: Mode of treatment set by your clinician. Options include: CPAP, Spontaneous, Spontaneous/Timed (VPAP III ST) and Timed

(VPAP III ST).

Ramping indicator: Appears if the VPAP is in ramp mode. This disappears once the ramp time has elapsed.

Set pressure(s): In CPAP mode, this displays the set treatment pressure

(units: centimetres of water). In other modes, it is exhalation and inhalation

pressures (units: centimetres of water).

Trigger indicator: How the VPAP changes the pressure when you are inhaling. "S" (Spontaneous) indicates a patient triggered change and "T" (Timed) indicates a device triggered change.

Pressure bar graph: Graphical display of the changing pressure.

Leak: Current mask leak (units: litres per minute).

Respiratory rate: Number of breaths per minute.

26

Image 33

Contents 248127/1 05 Illustrations 52 cm 3 m English Manufactured by Contents Limited Warranty Index Medical Information IntroductionUser/Owner Responsibility What the Vpap III and Vpap III ST are Intended forPage Medical Information Adverse EffectsPage Masks Vpap SystemHumidifiers AccessoriesSetting up the Vpap System Setting Up The VpapAttaching a Humidifier Attaching a HumidAire 2i Humidifier Attaching a HumidAire 2iC HumidifierAttaching a HumidAire Humidifier Attaching a Passover Humidifier LCD Screen Using the LCD Screen and KeypadKeypad Keys KeyFunction FrontRight red Key Function Left greenPage Starting Treatment Ramp timeStarting Treatment Using the HumidAire 2i Warm-Up Feature Using the Mask-Fitting FeatureStopping Treatment High Leak Page Daily Cleaning Cleaning and MaintenanceWeekly Cleaning Periodic CleaningServicing Replacing the Air FilterHow to Use the Vpap Menus How to Use the Standard MenuRamp Screen To exit out of the menu Press the Right key exit How to Use the Detailed Menu if enabled by your clinicianVpap Detailed Menu Series if enabled by your clinician Settings Menu Menu Functions Detailed menu onlyTo enter a submenu Press the Left key enter Settings for mask types Mask Function Default Function Description Setting OptionsSettings Mask Results Menu Function Function Description Setting OptionsResults Menu Servicing Menu Options MenuTreatment screen Treatment ScreensHow to Use the Vpap Menus Page Helpful Hints Using a Battery and an InverterStarting out Nasal IrritationPage Troubleshooting TroubleshootingCheck tube Key if done Problem Possible Cause SolutionLast session Page Dynamic pressure characteristics System SpecificationsFlow sensor in flow generator IEC 60601-1 ClassificationsPressure Variation Pressure Volume curvePressure cm H2O BreathsEnvironmental information Symbols which appear on the productEmissions test Compliance Next Portable and mobile RF communications Separation distance according to frequency of transmitter Limited Warranty Product Warranty PeriodLimited Warranty Page Index