RIDGID WD1950 manual Maintenance, Cord Wrap, Filter Filter Cleaning, Filter Removal

Page 13

SP6567 16 Gallon Steel.qxd 8/15/07 1:32 PM Page 13

Cord Wrap

When vacuuming is complete, unplug the cord and wrap it around the power assembly as shown. The cord should wrap under the pull handle (above the inlet) and around and under the cord wrap of the motor cover.

Push/Pull Handle

Cord Wrap

Power

Cord

Hose Storage

Area

Maintenance

Filter

!WARNING: To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter.

NOTE: The filter is made of high quality paper designed to stop very small particles of dust. The filter can be used for dry pick up or small amounts of liquid. Handle the filter carefully when removing to clean or installing it. Creases in the filter pleats may occur from installation but will not affect the performance of the filter.

Filter Cleaning

Your filter should be cleaned often to maintain peak vac performance.

Be sure to dry the filter before storing or picking up dry debris.

IMPORTANT: After cleaning, check the filter for tears or small holes. Do not use a filter with holes or tears in it. Even a small hole can cause a lot of dust to come out of your vac. Replace it immediately.

Filter Removal

To remove the filter for cleaning or replacement, unscrew the filter nut from the filter cage and lift off filter and filter plate .

IMPORTANT: To avoid damage to the

!WARNING: Do not operate with the filter cage and float removed. The float prevents water from entering the impeller and damaging the motor. The cage prevents fingers from touching the moving impeller.

blower wheel and motor, always reinstall the filter before using the vac for dry material pick-up.

Cleaning A Dry Filter

1.Some removal of dry debris can be accomplished without removing the filter from the vac. Slap your hand on top of the lid while the vac is turned off.

2.For best cleaning results due to accumulated dust, clean the filter in an open area. Cleaning SHOULD be done outdoors and not in the living quarters.

3.After filter removal from vac, remove the dry debris by gently tapping filter against the inside wall of your dust drum. The debris will loosen and fall.

4.For thorough cleaning of dry filter with fine dust (no debris), run water through it as described under "Cleaning A Wet Filter"

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents OPERATOR’S Manual Table of Contents Important Safety InstructionsExtension Cord Length Gauge A.W.G Turn off Vac before unpluggingIntroduction Unpacking and Checking Carton ContentsShaft Installing Handle Removing/Installing the Metal HandleInstalling Tool Holder Lowering Handle for StorageFilter Nut Lever Filter Plate Replacement Filter AssemblyFilter Filter Cage Filter Cage Slots TabsDrum/Caddy Assembly Insert Hose Wet/Dry Vac AssemblyVacuuming Dry Materials = OFFVacuuming Liquids Filter Sensor Reset ButtonFilter Performance Sensor Emptying the DrumBlowing Feature Accessory and StorageAccessory Storage Compartment Extension Wand OperationFilter Filter Cleaning MaintenanceCleaning a Dry Filter Cord WrapInstallation Cleaning a Wet FilterCleaning and Disinfecting the Wet/Dry Vac StorageTwist Backward Forward Latches Nozzle Body Removable InsertWhich Replacement Filter Meets Your Needs? Filter ReplacementApplications VF4000 Ent Keep YourRonm Envi CleaGallon Professional Wet/Dry Vac Model Number WD19500 Repair PartsKey Description Servicing of DOUBLE-INSULATED WET/DRY VAC Gallon Professional Wet/Dry Vac Cart Model Number WD19500 Repair Parts Emerson Tool Company Stock No. WD1950 Model No. WD19500 Serial NumberEmerson DivisionManual DEL Operador Sección IndiceGuarde Este Manual Lista del contenido de la caja de cartón IntroducciónDestornillador Phillips largo Martillo Clave DescripciónClave Descripción Clave Descripción CantInstalación del asa Remoción e instalación del asa metálicaBajada del asa para almacenar la aspiradora Remoción del asaEnsamblaje de un filtro de reemplazo DeCaptapaNut RuedaWheel Ensamblaje del tambor/base de soporteEjeShaft Raised RibIntroduzca la manguera Ensamblaje de la aspiradora para mojado/secoHandlesAsas Recogida de materiales secos con la aspiradora FuncionamientoBoquilla de uso general Boquilla que se usa en la Vaciado del tambor Sensor de rendimiento del filtroRecogida de líquidos con la aspiradora Accesorios y almacenamiento Funcionamiento continuaciónTraslado de la aspiradora para mojado/seco Dispositivo de sopladoMantenimiento Mantenimiento continuación Pestillos TwistExtraíble Delante¿Qué filtro de reemplazo es adecuado para sus necesidades? Reemplazo del filtroAplicaciones Edio Ambi Su m Lim Teng ¡ManTarj DólNo. de Clave Pieza Descripción Piezas de repuestoDe un cuadrado también esté marcado en los aparatos Bolsa de piezas sueltas no ilustrada Piezas de repuesto Emerson Professional Tools

WD1950 specifications

The RIDGID WD1950 is a powerful and versatile wet/dry vac that has garnered attention from both professionals and DIY enthusiasts alike. Designed for a variety of cleanup tasks, this vacuum combines performance with innovative features to make cleaning easier and more efficient.

One of the standout characteristics of the RIDGID WD1950 is its impressive 16-gallon capacity, which allows users to tackle large messes without the need for frequent emptying. This robust design makes it suitable for a variety of environments, from construction sites to home workshops. The vacuum is equipped with a potent 2.0 Peak HP motor, delivering a strong suction power that effectively handles a wide range of debris, from fine dust to heavy liquids.

Another key feature of the RIDGID WD1950 is its advanced filtration system. The vacuum utilizes a large, detachable filter that captures fine particles, ensuring that the air remains clean while you work. Designed to accommodate both wet and dry applications, the WD1950 features a replaceable foam sleeve for wet pickups, making it incredibly versatile for any cleanup job.

The RIDGID WD1950 is also built for user convenience and mobility. The vacuum comes with a durable hose that measures 7 feet in length, allowing users to reach tight spaces without hassle. The hose features a locking design to prevent accidental disconnection during operation. Additionally, the vacuum includes multiple attachments, such as a crevice tool and a utility nozzle, enabling users to customize their cleaning experience according to their needs.

The construction of the RIDGID WD1950 is robust and built to last. It features a sturdy and durable plastic tank that can withstand rough handling on job sites. The rear wheels are designed for stability and maneuverability, making it easy to transport the vacuum from one location to another.

In summary, the RIDGID WD1950 stands out for its powerful suction, large capacity, advanced filtration system, and user-friendly design. Whether it's for construction cleanup, car detailing, or general household chores, this wet/dry vac is equipped to handle the task efficiently. With its combination of functionality and durability, the RIDGID WD1950 is an indispensable tool for anyone in need of a reliable cleaning solution.
Top Page Image Contents