SSS AF9 manual Clearing blockages, Thermal Protector, If you have a problem

Page 11

49

A

C

B

Clearing blockages

Disconnect cleaner from electrical out- let.

Low suction or pick up may be due to a blockage in the system. Refer to the following steps to check for blockages

continuing with each step until the blockage is found:

1.Check fullness of filter bag; change if needed.

492. Plug cleaner in and turn ON. Check for suction at end of

hose (A).

a. If there is suction, turn cleaner OFF and continue with step 3.

b. If there is no suction, turn cleaner OFF and check for blockage in hose and dirt tube as follows:

1)Disconnect hose from dirt duct

(C) by reversing procedure for “Attach hose” on pg. 3, Fig. 7 and 8.

2)Clear out hose

3)Look into (C) and remove any blockage

3.Check connection at hose tube (B); remove any blockage.

4.Turn cleaner OFF and unplug.

50

D

5.Remove bottom plate, belt and agitator (see “The belt” section).

50Look into opening (D) for blockages and remove.

6.Remove agitator shield (see Fig. 44) and remove any loose debris which may have accumulated under it.

Thermal Protector

An internal thermal protector has been designed into your cleaner to protect it from overheating.

When the thermal protector acti- vates the cleaner will stop run- ning. If this happens proceed as fol- lows:

1.Turn cleaner OFF and disconnect it from the electrical outlet.

2.Check secondary and final filters for dirt accumulation.

3.Refer to “Clearing blockages” section.

4.When cleaner is unplugged and motor cools for 30 minutes, the ther- mal protector automatically resets and cleaning may continue.

If the thermal protector continues to activate after following the above steps, your cleaner may need ser- vicing (see “Service” section).

If you have a problem

If a minor problem occurs, it usually can be solved quite easily when the cause is found by using the check list below.

Problem: Cleaner won’t run

Possible cause

Possible solution

Not firmly plugged in

Plug unit in firmly

No voltage in wall plug

Check fuse or breaker

Blown fuse or tripped breaker

Replace fuse or reset breaker

Thermal protector activated

Allow cleaner to cool for 30 minutes (this will reset the thermal protector)

Problem: Cleaner/tools won’t pick up

Possible cause

Possible solution

Broken or worn belt

Replace belt

Agitator brush roll worn

Replace brush roll

Cloth/paper filter bag full

Empty/change filter bag

Incorrect carpet height setting

Move nozzle control knob to lower setting

Blockage in air flow passage

Clear blockage

Problem: Cleaner hard to push

Possible cause

Possible solution

Incorrect carpet height setting

Move nozzle control knob to lower setting

11

Image 11
Contents Serial Review these instructions before operating cleanerIndex English ppExtra belt Step I Unpack cartonStep III Attach Hose Furniture nozzle Hose hook Assembled cleaner will look like the drawing HandleGrounding instructions Hose20 C Carpet height adjustmentFor maximum cleaning perfor Cloth filter bag Stair cleaningSelect proper tool Attach wand and toolsHow to empty Secondary & final filters How to cleanOptional paper filter bag Belt How to replaceHeadlight Agitator brush roll Edge groomersThermal Protector If you have a problemClearing blockages Therefore, do not add lubricant to motor bearings ServiceLubrication Español pp IndiceLea estas instruc- ciones antes de usar la aspiradora Correa de repuesto una instalada en la aspiradora Instrucciones de conexión a tierraEscoja el acceso- rio adecuado Accesorios de limpiezaLimpieza de los Bordes Cómo limpiar los accesoriosLa correa Bolsa de filtro de papel opcionalFiltros secundario y final La luz delanteraProtector térmico Los limpiaorillasEl rodillo agitador Desatascamiento de obstruccionesLubricación ServicioFrançais pp ’aspirateur assemblé ressemble au dessin 12 1. Manche Instructions de mise à la terrePositions du Manche Accessoires de nettoyage Courroie Sac filtrant en papier optionnelLe filtre secondaire et le filtre final ÉclairageProtection thermique En cas de problèmeLes peignes latéraux Le rouleau-brosse de l’agitateurGraissage Réparations

AF9 specifications

The SSS AF9 is an advanced, high-performance concept introduced within the realm of small unmanned aerial vehicles (UAVs). Specifically designed for tactical applications, the AF9 boasts a range of features and technologies that enhance its operational capabilities.

One of the defining characteristics of the AF9 is its impressive flight endurance. With a capability to operate for extended durations, this UAV excels in reconnaissance and surveillance missions, providing invaluable real-time intelligence to decision-makers. The AF9’s ability to cover vast areas without the need for frequent landings sets it apart from many other drones in its category.

In terms of design, the SSS AF9 features a streamlined profile that ensures minimal drag and maximizes efficiency during flight. The airframe is constructed from lightweight composite materials, which not only reduces the overall weight but also enhances durability and resistance to environmental stresses. This construction contributes to the UAV's agility and speed, allowing it to maneuver effectively in varied terrains.

The AF9 is equipped with cutting-edge avionics and navigation systems. These technologies include advanced GPS and inertial navigation systems that facilitate precision tracking and positioning. Additionally, the UAV can operate autonomously or be controlled remotely, allowing flexible operational tactics based on mission requirements.

For payload versatility, the SSS AF9 supports various sensor packages and equipment, including high-resolution cameras, thermal imaging sensors, and electronic warfare devices. This modular capability allows operators to tailor the UAV for specific missions, be it intelligence, reconnaissance, or tactical support.

Communication technology is another crucial aspect of the SSS AF9. It employs secure, encrypted communication links, ensuring that data transmission remains confidential even in contested environments. This feature is vital for military operations where operational security is paramount.

Moreover, the SSS AF9 is designed with user-friendly interfaces, enabling operators to execute complex missions with ease. Comprehensive training programs are available to ensure that personnel can maximize the UAV's capabilities effectively.

In summary, the SSS AF9 represents a significant advancement in the field of tactical UAVs, combining flight endurance, advanced design, modularity, and secure communication technologies to meet the demands of modern operations. Its versatility enables it to adapt to a myriad of mission profiles, making it a reliable asset in various scenarios.