Spectra Watermakers Newport 400 owner manual 3/8, 1/2 Parker Tube Fitting Assembly

Page 16

Parker Tube Fitting Assembly Procedure

Spacer	Single grab ring for 1/4" & 3/8" tube
O-ring	Use 2 grab rings for 1/2" tube
Body	Nut
	Nut
	Tubing

Step 1: Dissemble fitting components

1/2" max

Step 2: Install the Nut first then use the bevelled side of the Spacer to push the Grab Ring onto the tube no more than 1/2". Slip the O-ring over the tube to hold the Spacer in place. If the Grab Ring is pushed too far, trim back the tube so about 1/4" of tube extends past the O-ring.

Step 3: Gently fit the tube into the body and loosely thread on the nut. Be careful not to cross-thread the nut

1/2" tube should not bottom out in the fitting to allow full compression of the O-ring

Step 4: Hand tighten the nut. DO NOT OVER TIGHTEN! DO NOT USE A WRENCH! The tube should not come out if pulled by hand. If it does, tighten the grab ring tabs.

1/4", 3/8", 1/2" Parker Tube Fitting Assembly

Image 16

Contents Page Page Newport Installation Quick Start Important Details for InstallerPage Table of Contents InstallationService & Maintenance OperationPage Getting Started Newport MkII shipping listInstallation Basics WiringThru-hulls Pipe Fitting InstructionComponent Placement Fresh Water Flush ModuleBoost Pump module Feed Pump ModuleClark Pump/Membrane Module Membrane Pressure Vessel MountingRemote Control Panel PlumbingSystem Piping schematic Page Product Water tubing Brine Discharge Fresh Water Flush3/8, 1/2 Parker Tube Fitting Assembly Parker Tube Fitting Assembly ProcedureWiring Component Sizing Wire Size Chart Newport MkII 12V DC System WiringMPC Remote Control Display Panels Connection of Optional Accessories Tank Switch Installation and Operation Page New System Start-Up and Testing Page Product Flow Dry Testing With Artificial Ocean Normal Operation Normal Start Up Using the Auto Run ButtonNormal Shut Down Flush Cycle Adjustment Automatic Store Cycle Manual Operation Long Term Storage Procedures System Storage or PicklingStorage Procedure Clean UpStorage & Winterizing Maintenance GeneralSeawater Strainer PrefiltersMembrane Cleaning MembranesCleaning Procedure Salinity Probe Calibration Spectra Watermakers parts list Part Number Suggested SparesMembrane Pressure Vessel Relocation Spectra High Pressure Tube Fitting Assembly Correct Torque is specification is 85 foot poundsSpectra Watermakers Newport Troubleshooting Procedures Error Messages Operation and Repair Bulletins MB-2 Membrane CareMB-5 Membrane Cleaning with Detergent MPC-5 Purge Mode Bypass OP-2 BAD Smelling Product Water PF-1 PREFILTERS- Vane Pump Systems PF-2 Charcoal Filters Brane Operation Manual Brane Power Harness Do not Disconnect Or Splice ANY High Voltage Wiring Clark Pump Front View Reversing Valve End Blocks Center Block Cylinder Assembly 10% Clark Pump Parts List

Newport 400 specifications

The Spectra Watermakers Newport 400 is a state-of-the-art desalination system designed for yachts and boats seeking reliable and efficient freshwater production. This innovative watermaker is known for its compact design, high performance, and user-friendly features. With the ability to produce up to 400 gallons of freshwater per day, the Newport 400 is ideal for extended cruising, offshore adventures, or as a backup water supply.

One of the standout features of the Newport 400 is its patented Spectra Reverse Osmosis technology. This advanced system harnesses the power of reverse osmosis to remove salt and impurities from seawater, ensuring the production of clean and safe drinking water. The Newport 400 operates with exceptional energy efficiency, requiring significantly less power compared to traditional watermakers. This is particularly beneficial for boats relying on limited energy sources like solar panels or generators.

The Newport 400 is engineered for ease of operation and maintenance with a user-friendly control panel. Operators can easily monitor key parameters such as water output, pressure, and system status. The intuitive interface makes it simple to adjust settings and troubleshoot potential issues. Additionally, the system is constructed from high-quality corrosion-resistant materials, ensuring durability and longevity in harsh marine environments.

An impressive characteristic of the Spectra Newport 400 is its ultra-quiet operation. This watermaker is designed to minimize noise, making it perfect for use in the close quarters of a yacht without disturbing the peace on board. The integration of advanced technologies further enhances its performance, including a sophisticated water pre-filtration system that reduces the risk of membrane fouling.

The Newport 400 is also designed with versatility in mind. It can be easily integrated into various onboard systems, allowing for simple installation and operation. Its compact size means it can fit into tight spaces on smaller vessels without sacrificing performance.

In summary, the Spectra Watermakers Newport 400 is a reliable, efficient, and quiet solution for generating freshwater in a marine environment. Its advanced reverse osmosis technology, ease of use, and robust construction make it an ideal choice for boaters seeking independence from shore-based water sources. Whether for leisurely cruising or serious ocean voyaging, the Newport 400 stands out as a top-tier watermaker for modern maritime adventures.