Windsor 10052410, SCX364 manual Solution Strainer, Changing Brush Motors

Page 27

5. SOLUTION STRAINER

The solution strainer is located in front of the left front wheel. The solution strainer protects the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris. Drain the solution tank and clean the solution strainer. To remove the strainer, turn the bottom part of the strainer counterclockwise until the bottom is separated. Clean out the debris from the wire mesh and re-assemble. Make sure the O-ring gasket is in place when re-assembled.

6. BRUSH MOTOR

Do not use a pressure washer to clean around the brush motors. Use tap pressure only.

CHANGING BRUSH MOTORS

1.With the scrub deck in the up position, disconnect brush motor wiring connector from harness.

2.Remove scrub brushes or pad drivers.

3.Remove retaining bolt, lock washer, flat washer and star drive from brush motor shaft.

4.Remove 4 brush motor mounting bolts located under scrub deck.

5.Remove brush motor.

6.Reverse steps to install.

MAINTENANCE

BRUSH MOTOR CARBON BRUSH REPLACEMENT

1.Remove the cover from the top of the motor by removing the three screws.

2.Note the alignment mark on motor barrel to motor cap. Remove three bolts.

3.Remove end cap with brushes from motor.

NOTE: Motors contain two wave washers in cap. Do not lose these.

4.Install the new end cap with brushes and realign with scribe marks on motor barrel. Reinstall the three attach bolts from cap into base.

5.Maintain alignment between motor barrel base and cap.

6.Install the cover on top of the motor with the three screws.

SCX364 86037150 1/17/07

4-9

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents Model HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls Propel Control Levers KEY SwitchEmergency SHUT-OFF Switch Brush SwitchSqueegee Deflection Adjustment Knobs Solution Control KnobVacuum Switch Squeegee Pitch Adjustment KnobBrush Pressure Indicator Parking Brake OptionalHour Meter PRE-RUN Machine Inspection Emergency Stop ProceduresFilling Solution Tank Machine OperationNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Double Scrub Emptying and Cleaning TanksSolution Tank Recovery TankMonthly HRS Service ScheduleMaintenance Maintenance Daily WeeklyMaintenance Batteries Battery MaintenanceBattery Condition Checking GravityTo Charge the Batteries Front of Machine Changing BatteriesTo Replace or Rotate Rear Squeegee Blade Adjusting SqueegeeTo Remove Squeegee Assembly Rear SqueegeeTo Adjust Amount of Rear Squeegee Deflection To Adjust Squeegee PitchUncoated Floors Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Scrub BrushesChanging Brush Motors Solution StrainerBrush Motor Carbon Brush Replacement Brush MotorBrush Skirts Traction Motor Carbon Brush ReplacementTraction Motor Circuit BreakersChanging Vacuum Motor Vacuum MotorScrub Deck IN-OUT Actuator Adjustment Actuator Scrub Deck UP- Down REMOVAL/REPLACEMENTScrub Deck UP-DOWN Actuator Adjustment Actuator Scrub Deck IN-OUT REMOVAL/REPLACEMENTTo Replace or Rotate Front Squeegee Blade Front SqueegeeCorrect Not Enough TOO Much Side View of Squeegee Blade To Adjust Front Squeegee DeflectionRecommended Greasing Machine Troubleshooting Problem CauseSolution Problem Cause Solution

10052410, SCX364 specifications

The Windsor SCX364, model number 10052410, is a sophisticated commercial-grade carpet extractor designed to deliver exceptional cleaning performance and efficiency in various settings, including hotels, offices, and retail spaces. This powerful machine offers a range of features and technologies aimed at ensuring superior floor care while also promoting operator ease and comfort.

One of the standout features of the Windsor SCX364 is its advanced suction system, which utilizes a high-efficiency vacuum motor. This motor not only enhances the extractor's cleaning ability but also aids in quick drying times, minimizing downtime and disruption in busy environments. The SCX364 is equipped with a large-capacity recovery tank, allowing for extended cleaning sessions without the need for frequent emptying, making it ideal for large areas.

Another critical technology integrated into the SCX364 is its dual-brush agitation system. This system employs two rotating brushes that work in unison to effectively loosen and lift dirt, stains, and debris from carpets. This dual-action approach ensures thorough cleaning and is particularly effective on high-traffic areas that may be more severely soiled.

In terms of operator comfort, the Windsor SCX364 features an ergonomic design that includes an adjustable handle and easy-to-use controls. These features enable operators to maneuver the machine effortlessly, even in tight spaces. Additionally, the lightweight construction of the SCX364 promotes ease of transport, allowing for convenient relocation between different areas.

The SCX364 is also designed with versatility in mind. It can accommodate a variety of cleaning solutions, enabling users to tailor their cleaning approach to different carpet types and soil levels. Its adjustable solution flow control allows operators to regulate water and detergent usage, optimizing cleaning performance while conserving resources.

In summary, the Windsor SCX364, model 10052410, is a high-performance carpet extractor that combines innovative technologies and user-oriented design. With its efficient suction system, dual-brush agitation, and adaptable settings, it stands out as a reliable choice for maintaining clean and inviting carpets in professional environments. Whether for routine maintenance or deep cleaning, the SCX364 delivers exceptional results, ensuring that carpets remain in excellent condition.
Top Page Image Contents