Windsor SCX364, 10052410 manual Checking Gravity, Battery Condition, To Charge the Batteries

Page 22

MAINTENANCE

CHECKING BATTERY SPECIFIC GRAVITY Use a hydrometer to check the battery specific gravity.

Battery Check

CHECKING GRAVITY

A.Hydrometer

B.Battery

NOTE: Do not take readings immediately after adding distilled water, if the water and acid are not thoroughly mixed, the reading may not be accurate.

Check the hydrometer readings against this chart.

SPECIFIC GRAVITY

 

@ 80° F (27°C)

BATTERY CONDITION

1.265

100% CHARGED

1.225

75% CHARGED

1.190

50% CHARGED

1.155

25% CHARGED

1.120

DISCHARGED

NOTE: If the readings are taken when the battery electrolyte is any temperature other than 80°F (27°C), the reading must be temperature corrected.

To find the corrected specific gravity reading when the temperature of the battery electrolyte is other than 80°F (27°): Add (+) to the specific gravity reading 0.004 (4 points), for each 10°F (6°C) above 80° (27°C).

Subtract (-) from the specific reading 0.004 (4 points), for each 10°F (6°C) below 80°F (27°C).

TO CHARGE THE BATTERIES

When servicing machine, avoid contact with battery acid.

Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging.

Wear eye protection and protective clothing when working with batteries.

Charge batteries in a well ventilated area. Leave the battery cover open.

Use a 24 volt, 18 amp maximum output or 25 amp (depending on the size of the batteries), DC charger which will automatically shut off when the batteries are fully charged.

1.Stop the machine in a clean, well-ventilated area next to the charger.

2.Turn “OFF” machine.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

3.Raise the battery cover.

Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging.

4.Check the electrolyte level in each battery cell. Before charging, add just enough distilled water to cover the plates. After charging is complete, add just enough distilled water to bring up the level to the indicator ring. If the water level is too high before charging, normal expansion rate of the electrolyte may cause an overflow. Resulting in a loss of battery acid balance and damage the machine.

5.Replace the battery caps, and leave them in place while charging.

6.Unplug the battery connector from the machine.

4-4

SCX364 86037150 1/17/07

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Walk Behind Scrubber Your Dealer Machine Data LOG/OVERVIEWOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls Brush Switch KEY SwitchEmergency SHUT-OFF Switch Propel Control LeversSqueegee Pitch Adjustment Knob Solution Control KnobVacuum Switch Squeegee Deflection Adjustment KnobsParking Brake Optional Brush Pressure IndicatorHour Meter Machine Operation Emergency Stop ProceduresFilling Solution Tank PRE-RUN Machine InspectionTo Begin Scrubbing Normal ScrubbingTo Stop Scrubbing Recovery Tank Emptying and Cleaning TanksSolution Tank Double ScrubMaintenance Daily Weekly Service ScheduleMaintenance Monthly HRSMaintenance Battery Maintenance BatteriesChecking Gravity Battery ConditionTo Charge the Batteries Changing Batteries Front of MachineRear Squeegee Adjusting SqueegeeTo Remove Squeegee Assembly To Replace or Rotate Rear Squeegee BladeTo Adjust Squeegee Pitch To Adjust Amount of Rear Squeegee DeflectionScrub Brushes Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Uncoated FloorsBrush Motor Solution StrainerBrush Motor Carbon Brush Replacement Changing Brush MotorsCircuit Breakers Traction Motor Carbon Brush ReplacementTraction Motor Brush SkirtsVacuum Motor Changing Vacuum MotorActuator Scrub Deck IN-OUT REMOVAL/REPLACEMENT Actuator Scrub Deck UP- Down REMOVAL/REPLACEMENTScrub Deck UP-DOWN Actuator Adjustment Scrub Deck IN-OUT Actuator AdjustmentFront Squeegee To Replace or Rotate Front Squeegee BladeTo Adjust Front Squeegee Deflection Correct Not Enough TOO Much Side View of Squeegee BladeRecommended Greasing Problem Cause Machine TroubleshootingSolution Problem Cause Solution

10052410, SCX364 specifications

The Windsor SCX364, model number 10052410, is a sophisticated commercial-grade carpet extractor designed to deliver exceptional cleaning performance and efficiency in various settings, including hotels, offices, and retail spaces. This powerful machine offers a range of features and technologies aimed at ensuring superior floor care while also promoting operator ease and comfort.

One of the standout features of the Windsor SCX364 is its advanced suction system, which utilizes a high-efficiency vacuum motor. This motor not only enhances the extractor's cleaning ability but also aids in quick drying times, minimizing downtime and disruption in busy environments. The SCX364 is equipped with a large-capacity recovery tank, allowing for extended cleaning sessions without the need for frequent emptying, making it ideal for large areas.

Another critical technology integrated into the SCX364 is its dual-brush agitation system. This system employs two rotating brushes that work in unison to effectively loosen and lift dirt, stains, and debris from carpets. This dual-action approach ensures thorough cleaning and is particularly effective on high-traffic areas that may be more severely soiled.

In terms of operator comfort, the Windsor SCX364 features an ergonomic design that includes an adjustable handle and easy-to-use controls. These features enable operators to maneuver the machine effortlessly, even in tight spaces. Additionally, the lightweight construction of the SCX364 promotes ease of transport, allowing for convenient relocation between different areas.

The SCX364 is also designed with versatility in mind. It can accommodate a variety of cleaning solutions, enabling users to tailor their cleaning approach to different carpet types and soil levels. Its adjustable solution flow control allows operators to regulate water and detergent usage, optimizing cleaning performance while conserving resources.

In summary, the Windsor SCX364, model 10052410, is a high-performance carpet extractor that combines innovative technologies and user-oriented design. With its efficient suction system, dual-brush agitation, and adaptable settings, it stands out as a reliable choice for maintaining clean and inviting carpets in professional environments. Whether for routine maintenance or deep cleaning, the SCX364 delivers exceptional results, ensuring that carpets remain in excellent condition.
Top Page Image Contents