Windsor 10052410, SCX364 manual Changing Batteries, Front of Machine

Page 23

FOR SAFETY: When charging, connect the charger to the batteries before connecting the charger to the AC wall outlet. Never connect the charger to the AC wall outlet first. Hazardous sparks may result.

7. Plug the charger connector into the battery connector. Connect the charger AC plug to a wall outlet. The charger gauge should indicate that the batteries are charging.

8.When the batteries are fully charged, disconnect the charger from the AC wall outlet, then disconnect the charger from the batteries.

9.Connect the batteries to the machine connector.

10.Check the electrolyte level. It should be up to the indicator ring. If necessary, add distilled water.

11.Lower the battery cover.

1.Current level being delivered to the batteries will be displayed on the charger’s bar graph.

2.When battery charge level has reached 80% the YELLOW “80%” LED will light.

3.Batteries will then receive a low current “finish-charge” indicated by the flashing GREEN “100%” LED.

4.Charging cycle is complete when “100%” LED is continuously GREEN.

5.Disconnect charger’s AC power cord.

6.Raise battery cover and check the battery electrolyte level. It should be up to the indicator ring. If necessary, add distilled water.

7.Lower the battery cover.

CHANGING BATTERIES

Stop the machine in a clean area next to the charger. Turn off machine.

FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn off machine and remove key.

1.Raise the battery cover.

2.Disconnect battery pack from machine.

3.Use the proper size open-end wrench to disconnect main ground wire first and secure cable terminal away from batteries.

4.Disconnect main positive lead and secure cable terminals away from batteries.

5.Loosen both terminals on each jumper cable and remove one at a time.

6.Prepare a suitable site to place the batteries.

7.Attach suitable battery lifting device and lift batteries from the machine.

MAINTENANCE

Batteries are a potential environmental hazard. Consult your battery supplier for safe disposal methods.

+

+

-

RED

RED

BLK

BLK

BLK

RED

-

-

+

+

-

-

RED

BLK

BLK

BLK-

RED+

RED+

FRONT OF MACHINE

SCX364 86037150 03/14/07

4-5

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Walk Behind Scrubber Overview Machine Data LOG/OVERVIEWYour Dealer Table of Contents Model HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls Propel Control Levers KEY SwitchEmergency SHUT-OFF Switch Brush SwitchSqueegee Deflection Adjustment Knobs Solution Control KnobVacuum Switch Squeegee Pitch Adjustment KnobHour Meter Brush Pressure IndicatorParking Brake Optional PRE-RUN Machine Inspection Emergency Stop ProceduresFilling Solution Tank Machine OperationTo Stop Scrubbing Normal ScrubbingTo Begin Scrubbing Double Scrub Emptying and Cleaning TanksSolution Tank Recovery TankMonthly HRS Service ScheduleMaintenance Maintenance Daily WeeklyMaintenance Batteries Battery MaintenanceTo Charge the Batteries Battery ConditionChecking Gravity Front of Machine Changing BatteriesTo Replace or Rotate Rear Squeegee Blade Adjusting SqueegeeTo Remove Squeegee Assembly Rear SqueegeeTo Adjust Amount of Rear Squeegee Deflection To Adjust Squeegee PitchUncoated Floors Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Scrub BrushesChanging Brush Motors Solution StrainerBrush Motor Carbon Brush Replacement Brush MotorBrush Skirts Traction Motor Carbon Brush ReplacementTraction Motor Circuit BreakersChanging Vacuum Motor Vacuum MotorScrub Deck IN-OUT Actuator Adjustment Actuator Scrub Deck UP- Down REMOVAL/REPLACEMENTScrub Deck UP-DOWN Actuator Adjustment Actuator Scrub Deck IN-OUT REMOVAL/REPLACEMENTTo Replace or Rotate Front Squeegee Blade Front SqueegeeCorrect Not Enough TOO Much Side View of Squeegee Blade To Adjust Front Squeegee DeflectionRecommended Greasing Solution Machine TroubleshootingProblem Cause Problem Cause Solution

10052410, SCX364 specifications

The Windsor SCX364, model number 10052410, is a sophisticated commercial-grade carpet extractor designed to deliver exceptional cleaning performance and efficiency in various settings, including hotels, offices, and retail spaces. This powerful machine offers a range of features and technologies aimed at ensuring superior floor care while also promoting operator ease and comfort.

One of the standout features of the Windsor SCX364 is its advanced suction system, which utilizes a high-efficiency vacuum motor. This motor not only enhances the extractor's cleaning ability but also aids in quick drying times, minimizing downtime and disruption in busy environments. The SCX364 is equipped with a large-capacity recovery tank, allowing for extended cleaning sessions without the need for frequent emptying, making it ideal for large areas.

Another critical technology integrated into the SCX364 is its dual-brush agitation system. This system employs two rotating brushes that work in unison to effectively loosen and lift dirt, stains, and debris from carpets. This dual-action approach ensures thorough cleaning and is particularly effective on high-traffic areas that may be more severely soiled.

In terms of operator comfort, the Windsor SCX364 features an ergonomic design that includes an adjustable handle and easy-to-use controls. These features enable operators to maneuver the machine effortlessly, even in tight spaces. Additionally, the lightweight construction of the SCX364 promotes ease of transport, allowing for convenient relocation between different areas.

The SCX364 is also designed with versatility in mind. It can accommodate a variety of cleaning solutions, enabling users to tailor their cleaning approach to different carpet types and soil levels. Its adjustable solution flow control allows operators to regulate water and detergent usage, optimizing cleaning performance while conserving resources.

In summary, the Windsor SCX364, model 10052410, is a high-performance carpet extractor that combines innovative technologies and user-oriented design. With its efficient suction system, dual-brush agitation, and adaptable settings, it stands out as a reliable choice for maintaining clean and inviting carpets in professional environments. Whether for routine maintenance or deep cleaning, the SCX364 delivers exceptional results, ensuring that carpets remain in excellent condition.
Top Page Image Contents