Windsor SCX364, 10052410 Double Scrub, Emptying and Cleaning Tanks, Solution Tank, Recovery Tank

Page 18

MACHINE OPERATION

DOUBLE SCRUB

For floors which are heavily soiled or have thick accumulations of floor finish may not clean sufficiently with one pass. In these cases it will be necessary to double scrub.

To double scrub, make the first pass over the surface being cleaned with both squeegees up, vacuum off, the solution on and brushes down. This allows the solution to stay in contact with the soil while loosening the surface accumulation with the brushes. Allow time for the first application to stay in contact with the floor. Length of time between the first and second pass depends on amount of accumulation and the type of chemical being used. A second scrubbing with both squeegees down and again the solution and brushes on will further loosen soil. The additional application of solution will further assist the difficult cleaning job.

FOR SAFETY: When using machine, go slow on inclines and slippery services.

EMPTYING AND CLEANING TANKS

1.Park the machine next to a floor drain. Drain hose is on left rear corner of the machine.

2.Turn the machine power off and set parking brake, if your machine is equipped with this option.

SOLUTION TANK

1.Loosen small drain hose from the retainer, then lower hose in direction of the drain.

2.Remove the solution tank cover.

3.Flush the solution tank out with clean water and run several gallons of clean water through systems. Do not use water hotter than 140°F (60°C) to clean tank. Damage may occur.

NOTE: Never allow solution to remain in tank. Damage to tank, seals and valves could occur.

4.Secure drain hose into the retainer.

RECOVERY TANK

1.Unhook the large drain hose from the retainer. Lower hose in direction of the drain then unscrew the T-handle on plug enough to loosen plug. Do not stand in front of end of hose. Recovered solution will come out with force. Slowly remove plug from drain hose.

2.Remove the recovery tank dome. Flush the recovery tank out with clean water. Do not use water hotter than 140°F (60°C) to clean tank. Damage may occur.

3.Clean off the float shut-off system and inspect for free movement of float. The float shut-off system is located in the rear of the recovery tank.

4.Replace the drain plug and secure drain hose in bracket.

5.If machine is to be stored, leave the recovery tank dome off.

RECOVERY

TANK COVER

SOLUTION

TANK COVER

RECOVERY

TANK DRAIN

SOLUTION

TANK DRAIN

3-11

SCX364 86037150 1/17/07

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls Brush Switch KEY SwitchEmergency SHUT-OFF Switch Propel Control LeversSqueegee Pitch Adjustment Knob Solution Control KnobVacuum Switch Squeegee Deflection Adjustment KnobsBrush Pressure Indicator Parking Brake OptionalHour Meter Machine Operation Emergency Stop ProceduresFilling Solution Tank PRE-RUN Machine InspectionNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Recovery Tank Emptying and Cleaning TanksSolution Tank Double ScrubMaintenance Daily Weekly Service ScheduleMaintenance Monthly HRSMaintenance Battery Maintenance BatteriesBattery Condition Checking GravityTo Charge the Batteries Changing Batteries Front of MachineRear Squeegee Adjusting SqueegeeTo Remove Squeegee Assembly To Replace or Rotate Rear Squeegee BladeTo Adjust Squeegee Pitch To Adjust Amount of Rear Squeegee DeflectionScrub Brushes Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Uncoated FloorsBrush Motor Solution StrainerBrush Motor Carbon Brush Replacement Changing Brush MotorsCircuit Breakers Traction Motor Carbon Brush ReplacementTraction Motor Brush SkirtsVacuum Motor Changing Vacuum MotorActuator Scrub Deck IN-OUT REMOVAL/REPLACEMENT Actuator Scrub Deck UP- Down REMOVAL/REPLACEMENTScrub Deck UP-DOWN Actuator Adjustment Scrub Deck IN-OUT Actuator AdjustmentFront Squeegee To Replace or Rotate Front Squeegee BladeTo Adjust Front Squeegee Deflection Correct Not Enough TOO Much Side View of Squeegee BladeRecommended Greasing Machine Troubleshooting Problem CauseSolution Problem Cause Solution

10052410, SCX364 specifications

The Windsor SCX364, model number 10052410, is a sophisticated commercial-grade carpet extractor designed to deliver exceptional cleaning performance and efficiency in various settings, including hotels, offices, and retail spaces. This powerful machine offers a range of features and technologies aimed at ensuring superior floor care while also promoting operator ease and comfort.

One of the standout features of the Windsor SCX364 is its advanced suction system, which utilizes a high-efficiency vacuum motor. This motor not only enhances the extractor's cleaning ability but also aids in quick drying times, minimizing downtime and disruption in busy environments. The SCX364 is equipped with a large-capacity recovery tank, allowing for extended cleaning sessions without the need for frequent emptying, making it ideal for large areas.

Another critical technology integrated into the SCX364 is its dual-brush agitation system. This system employs two rotating brushes that work in unison to effectively loosen and lift dirt, stains, and debris from carpets. This dual-action approach ensures thorough cleaning and is particularly effective on high-traffic areas that may be more severely soiled.

In terms of operator comfort, the Windsor SCX364 features an ergonomic design that includes an adjustable handle and easy-to-use controls. These features enable operators to maneuver the machine effortlessly, even in tight spaces. Additionally, the lightweight construction of the SCX364 promotes ease of transport, allowing for convenient relocation between different areas.

The SCX364 is also designed with versatility in mind. It can accommodate a variety of cleaning solutions, enabling users to tailor their cleaning approach to different carpet types and soil levels. Its adjustable solution flow control allows operators to regulate water and detergent usage, optimizing cleaning performance while conserving resources.

In summary, the Windsor SCX364, model 10052410, is a high-performance carpet extractor that combines innovative technologies and user-oriented design. With its efficient suction system, dual-brush agitation, and adaptable settings, it stands out as a reliable choice for maintaining clean and inviting carpets in professional environments. Whether for routine maintenance or deep cleaning, the SCX364 delivers exceptional results, ensuring that carpets remain in excellent condition.
Top Page Image Contents