Windsor 10052410, SCX364 manual To Replace or Rotate Front Squeegee Blade

Page 31

13. FRONT SQUEEGEE

The front blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has two wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use.

The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job. As with the front, each squeegee blade assembly has two wear surfaces for extended service.

Check both the front and rear squeegee blades for damage, wear, and adjustment each day in the pre- run check. Change the front blade if it is torn or has an uneven edge. Change the rear blade if it is less than 1/2 the original thickness.

ADJUSTING SQUEEGEE

The squeegee assembly must have correct deflection at each tip as well as the center. The knobs on the squeegee linkage control the adjustment.

TO REMOVE SQUEEGEE ASSEMBLY

1.With the squeegee and deck in the up position, and the swinging deck in the out position, turn key switch “OFF”.

2.Disconnect vacuum hose from squeegee and loosen both mounting knobs.

3.Pull squeegee assembly rearward from the lifting carrier.

4.Inspect or repair as necessary and reinstall.

MAINTENANCE

TO REPLACE OR ROTATE REAR SQUEEGEE BLADE

1.With the squeegee and deck in the up position, and the swinging deck in the out position, turn key switch “OFF”.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

2.Remove the squeegee assembly from the machine. Unscrew the retaining nuts and remove blade retainer strap and remove squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has two edge positions.

4.Install blade on locating pins of squeegee assembly.

5.Install squeegee retainer strap.

6.Fasten only tight enough to take up slack in retaining strap.

TO REPLACE OR ROTATE FRONT SQUEEGEE BLADE

1.With the squeegee and deck in the up position, and the swinging deck in the out position, turn key switch “OFF”.

2.Remove the squeegee from the machine. Remove retaining nuts then remove the retainer strap and squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has two edge positions. When installing the front blade, tighten the center nut first. Insure that the retainer strap is pressed against the blade before tightening the outer nuts.

SCX364 86037150 1/17/07

4-13

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Walk Behind Scrubber Your Dealer Machine Data LOG/OVERVIEWOverview Table of Contents Model HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls Propel Control Levers KEY SwitchEmergency SHUT-OFF Switch Brush SwitchSqueegee Deflection Adjustment Knobs Solution Control KnobVacuum Switch Squeegee Pitch Adjustment KnobParking Brake Optional Brush Pressure IndicatorHour Meter PRE-RUN Machine Inspection Emergency Stop ProceduresFilling Solution Tank Machine OperationTo Begin Scrubbing Normal ScrubbingTo Stop Scrubbing Double Scrub Emptying and Cleaning TanksSolution Tank Recovery TankMonthly HRS Service ScheduleMaintenance Maintenance Daily WeeklyMaintenance Batteries Battery MaintenanceChecking Gravity Battery ConditionTo Charge the Batteries Front of Machine Changing BatteriesTo Replace or Rotate Rear Squeegee Blade Adjusting SqueegeeTo Remove Squeegee Assembly Rear SqueegeeTo Adjust Amount of Rear Squeegee Deflection To Adjust Squeegee PitchUncoated Floors Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Scrub BrushesChanging Brush Motors Solution StrainerBrush Motor Carbon Brush Replacement Brush MotorBrush Skirts Traction Motor Carbon Brush ReplacementTraction Motor Circuit BreakersChanging Vacuum Motor Vacuum MotorScrub Deck IN-OUT Actuator Adjustment Actuator Scrub Deck UP- Down REMOVAL/REPLACEMENTScrub Deck UP-DOWN Actuator Adjustment Actuator Scrub Deck IN-OUT REMOVAL/REPLACEMENTTo Replace or Rotate Front Squeegee Blade Front SqueegeeCorrect Not Enough TOO Much Side View of Squeegee Blade To Adjust Front Squeegee DeflectionRecommended Greasing Problem Cause Machine TroubleshootingSolution Problem Cause Solution

10052410, SCX364 specifications

The Windsor SCX364, model number 10052410, is a sophisticated commercial-grade carpet extractor designed to deliver exceptional cleaning performance and efficiency in various settings, including hotels, offices, and retail spaces. This powerful machine offers a range of features and technologies aimed at ensuring superior floor care while also promoting operator ease and comfort.

One of the standout features of the Windsor SCX364 is its advanced suction system, which utilizes a high-efficiency vacuum motor. This motor not only enhances the extractor's cleaning ability but also aids in quick drying times, minimizing downtime and disruption in busy environments. The SCX364 is equipped with a large-capacity recovery tank, allowing for extended cleaning sessions without the need for frequent emptying, making it ideal for large areas.

Another critical technology integrated into the SCX364 is its dual-brush agitation system. This system employs two rotating brushes that work in unison to effectively loosen and lift dirt, stains, and debris from carpets. This dual-action approach ensures thorough cleaning and is particularly effective on high-traffic areas that may be more severely soiled.

In terms of operator comfort, the Windsor SCX364 features an ergonomic design that includes an adjustable handle and easy-to-use controls. These features enable operators to maneuver the machine effortlessly, even in tight spaces. Additionally, the lightweight construction of the SCX364 promotes ease of transport, allowing for convenient relocation between different areas.

The SCX364 is also designed with versatility in mind. It can accommodate a variety of cleaning solutions, enabling users to tailor their cleaning approach to different carpet types and soil levels. Its adjustable solution flow control allows operators to regulate water and detergent usage, optimizing cleaning performance while conserving resources.

In summary, the Windsor SCX364, model 10052410, is a high-performance carpet extractor that combines innovative technologies and user-oriented design. With its efficient suction system, dual-brush agitation, and adaptable settings, it stands out as a reliable choice for maintaining clean and inviting carpets in professional environments. Whether for routine maintenance or deep cleaning, the SCX364 delivers exceptional results, ensuring that carpets remain in excellent condition.
Top Page Image Contents