Wayne-Dalton 9300 Table of Contents, Definition of key words used in this manual

Page 2

Table of Contents

 

Important Safety Instructions

2

Package Contents

3

Door Section Identification

4

Tools Required

5

Pre-Installation

3-6

Removing An Existing Door

5

Preparing The Opening

6

Installation

7-22

Torquemaster Plus Reset Instructions

23-25

Optional Installations

25-26

Side Lock

25

Pull Rope

26

Trolley Operator

26

Maintenance

26

Cleaning

26

Warranty

27

Customer Service Number

28

Definition of key words used in this manual:

WARNING

INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN SEVERE OR FATAL INJURY.

CAUTION: PROPERTY DAMAGE OR INJURY CAN RESULT FROM FAILURE TO FOLLOW INSTRUCTIONS.

IMPORTANT: REQUIRED STEP FOR SAFE AND PROPER DOOR OPERATION.

NOTE: Information assuring proper installation of the door.

WARNING

TO AVOID POSSIBLE INJURY, READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING INSTALLATION. IF IN QUESTION ABOUT ANY OF THE PROCEDURES, DO NOT PERFORM THE WORK. INSTEAD, HAVE A TRAINED DOOR SYSTEMS TECHNICIAN DO THE INSTALLATION OR REPAIRS.

1.READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

2.Wear protective gloves during installation to avoid possible cuts from sharp metal edges.

3.It is always recommended to wear eye protection when using tools, otherwise eye injury could result.

4.Avoid installing your new door on windy days. Door could fall during the installation causing severe or fatal injury.

5.Doors 12’- 0” wide and wider should be installed by two persons, to avoid possible injury.

6.Operate door ONLY when it is properly adjusted and free from obstructions.

7.If a door becomes hard to operate, inoperative or is damaged, immediately have necessary adjustments and/or repairs made by a trained door system technician using proper tools and instructions.

8.DO NOT stand or walk under a moving door, or permit anybody to stand or walk under an electrically operated door.

9.DO NOT place fingers or hands into open section joints when closing a door. Use lift handles/gripping points when operating door manually.

10.DO NOT permit children to operate garage door or door controls. Severe or fatal injury could result, should the child become entrapped between the door and the floor.

11.Due to constant extreme spring tension, DO NOT attempt any adjustment, repair or alteration to any part of the door, especially to springs, spring brackets, bottom corner brackets, red colored fasteners, cables or supports. To avoid possible severe or fatal injury, have any such work performed

by a trained door systems technician using proper tools and instructions.

12.On electrically operated doors, pull down ropes must be removed and locks must be removed or made inoperative in the open (unlocked) position.

13.Top section of door may need to be reinforced when attaching an electric opener. Check door and/or opener manufacturer’s instructions.

14.VISUALLY inspect door and hardware monthly for worn and or broken parts. Check to ensure door operates freely.

15.Test electric opener’s safety features monthly, following opener manufacturer’s instructions.

16.NEVER hang tools, bicycles, hoses, clothing or anything else from horizontal tracks. Track systems are not intended or designed to support extra weight.

17.Avoid installing your door in close proximity to any heat source that may exceed 200° F. Failure to due so, may cause door sections to

blister and/or warp.

After installation is complete, fasten this manual near garage door.

2

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Series Copyright 2008 Wayne-Dalton CorpTable of Contents Definition of key words used in this manualPackage Contents Lock Stile Door Section IdentificationOperator Stile Side View AstragalGloves Tools RequiredRemoving An Existing Door SAW Horses Pair Step LadderTools from Preparing the OpeningTools Needed Must be ReplacedQuick Install TAB Locked InstallationAttaching Quick Install Flag Angle to Vertical TrackTo Vertical Track Horizontal AngleTOP Installing Q.I. Jamb BracketsRight Side Shown 3RD SET HolesBuilding Looking OUT DrumsAllowing door to fall, possibly Important the Tops Bottom SectionVertical Track ShimTop Bracket Slide 4 20 x 1 carriage boltsDoor Operation Important the DimensionTop Section Nail TOP SectionAttaching Horizontal Track to Quick Install FlagangleFully Adjustable Flagangle Attaching Horizontal Track toTorquemaster Spring Tube Assembly Labeled END Adjusting Top Bracket SlideAssembly TorqueMaster Spring TubeCable Drums Center Bracket AssemblyCenter Bracket Assembly Torquemaster Spring Tube 2 Wrap ShownRight END Bracket Groove SplinesTAG HEX Head LAGTened to Header Securing Center Bracket AssemblySecuring Door For Spring WindingHands Cable AdjustmentWinding Springs Recommended Spring TurnsFrom Vertical Tracks Important Pawl Knob Must beTag Tabs Engage the Third RIBUP Position Rear SupportDoor VicePerforated Angle Bolts & Nuts TorqueMaster Plus Reset InstructionsImportant be Prepared to Support Total Weight of the Door Spring DoorsSide Lock Unlocked Position if ANTrolley Operator CleaningPull Rope Limited Warranty Model Thank you for your purchase

9300 specifications

The Wayne-Dalton 9300 is a high-quality insulated steel garage door renowned for its durability, energy efficiency, and aesthetic appeal. Designed to meet a range of residential needs, the 9300 series combines performance with style, making it a popular choice among homeowners.

One of the standout features of the Wayne-Dalton 9300 is its construction. The door consists of a robust, 2-inch thick panel that is filled with high-density polystyrene insulation. This insulation not only provides excellent thermal performance but also contributes to the door's overall strength. With an R-value of up to 13.4, the 9300 series helps maintain a comfortable temperature in the garage while reducing energy costs for heating or cooling adjacent spaces.

In terms of design flexibility, the Wayne-Dalton 9300 is available in a variety of colors and finishes, allowing homeowners to match their garage doors to their home’s exterior. The door is constructed using steel that is pre-painted and baked with a tough finish to resist fading, chipping, and denting. Homeowners can choose from various contemporary and traditional styles, ensuring a perfect fit for any architectural design.

The Wayne-Dalton 9300 also incorporates advanced technology, such as the TorqueMaster® lifting system. This innovative system provides a torsion spring lift that is safely contained within the door's structure, reducing the risk of injury and ensuring smooth operation. Additionally, the 9300 series comes equipped with high-quality weather seals that protect against wind, rain, and snow, enhancing the door’s performance in various weather conditions.

Moreover, the 9300 series emphasizes safety features, including pinch-resistant design, which helps to prevent fingers from getting caught during operation. The doors also utilize high-performance rollers and sturdy hardware to ensure reliable, quiet, and long-lasting operation.

In summary, the Wayne-Dalton 9300 is an excellent choice for those seeking a durable, energy-efficient, and stylish garage door. With its advanced insulation technology, variety of design options, innovative lifting system, and emphasis on safety, the 9300 series stands out as a top contender in the market for residential garage doors. It offers homeowners peace of mind while enhancing the overall curb appeal of their property.
Top Page Image Contents