Wayne-Dalton 46 installation instructions Table of Contents

Page 2

Table of Contents

 

Important Safety Instructions

2

Package Contents

3-4

Door Section Identification

4

Tools Required

5

Pre-Installation

5-10

Removing The Old Door

5-9

Preparing The Opening

10

Installation

11-32

Optional Installations

33-35

Side Lock

33

DoorMasterTM Bracket

33

Alternative Step Plate

34

Pull Rope

34

Trolley Operator

35

Maintenance

36

Cleaning

36

Painting Instructions

36

Warranty

37

Dealer Locator Information

38

Definition of key words used in this manual:

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in severe or fatal injury.

CAUTION: PROPERTY DAMAGE OR INJURY CAN RESULT FROM FAILURE TO FOLLOW INSTRUCTIONS.

IMPORTANT: Required step for safe and proper door operation.

NOTE: Information assuring proper installation of the door.

2

WARNING

Read these instructions carefully before attempting installation. If in question about any of the procedures, do not perform the work. Instead, have a qualified door agency do the installation or repairs.

1.Read and follow all installation instructions.

2.Wear protective gloves during installation to avoid possible cuts from sharp metal edges.

3.It is always recommended to wear eye protection when using tools, otherwise severe or fatal eye injury could result.

4.Avoid installing your new door on windy days. Door could fall during the instazllation causing severe or fatal injury.

5.Doors 12’-0” wide and wider should be installed by two persons, to avoid possible injury.

6.Operate door ONLY when it is properly adjusted and free from obstructions.

7.If a door becomes hard to operate, inoperative or is damaged, immediately have necessary adjustments and/or repairs made by a trained door system technician using proper tools and instructions.

8.DO NOT stand or walk under a moving door, or permit anybody to stand or walk under an electrically operated door.

9.DO NOT place fingers or hands into open section joints when closing a door. Use lift handles/gripping points when operating door manually.

10.DO NOT permit children to operate garage door or door controls. Severe or fatal injury could result, should the child become entrapped between the door and the floor.

11.Due to constant extreme spring tension, DO NOT attempt any adjustment, repair or alteration to any part of the door, especially to springs, spring brackets, bottom corner brackets, red colored fasteners, cables or supports. To avoid possible severe or fatal injury, have any such work performed

by a trained door systems technician using proper tools and instructions.

12.On electrically operated doors, pull down ropes must be removed and locks must be removed or made inoperative in the open (unlocked) position.

13.Top section of door may need to be reinforced when attaching an electric opener. Check door and/or opener manufacturer’s instructions.

14.VISUALLY inspect door and hardware monthly for worn and or broken parts. Check to ensure door operates freely.

15.Test electric opener’s safety features monthly, following opener manufacturer’s instructions.

16.NEVER hang tools, bicycles, hoses, clothing or anything else from horizontal tracks. Track systems are not intended or designed to support extra weight.

After installation is complete, fasten this manual near garage door.

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Series, Model Portland Source PlantTable of Contents Package Contents Package Contents Door Section IdentificationTools Required Winding bars can cause spring Torsion Spring Removal For Standard LiftFailure to use approved Door agency release the tensionTorqueMaster Spring Removal Left hand side Assembly off the flagangles and outEither direction. If the counterbalance Applications, repeat for left hand sideExtension Spring Removal Removing the Old DoorSecurely attach a Preparing the OpeningFailure to Suitable mounting pad to structurallyAttaching Fully Adjustable Flagangle to Vertical TrackBottom Bracket Installing Fully Adjustable JambBrackets Counterbalance DrumsLeft hand Roller Hinge tubeHinges Top Bracket Step PlateAbove top bracket and secure with Installation on the Top SectionInstallation on all other All glazed doors starting at 14’0 widthLift Handle Bottom SectionVertical Track Stacking SectionsTop Section Adjusting Top Brackets Horizontal TrackTorqueMaster Spring Tube Center Bracket BushingOpener back and forth slightly to help Idrive InstallationPlug the motor power cord into Opener Aid alignmentCable Drum Installation Drive Gear Installation End BracketsCounter Installation Securing Center Bracket BushingPositioning Support Bracket Mounting Disconnect Handle BracketHandle until snug, and then tighten Attaching Disconnect HandleDisconnect handle bracket. Tighten Secure disconnect cable toFor Spring Winding Cable AdjustmentsSecuring Door Winding Bolt Rotation Ing adjustments toSetting Spring Tension Prior to winding or makKeep horizontal track Drum Wrap InstallationRear Support Parallel and within 3/4May release from spring Installation InstructionsOtherwise, the spring fittings If not wound in the properSide Lock Pull Rope Trolley Operator Painting CleaningCleaning Your Garage Door Limited Warranty Models 8000, 8100, 8200 Thank you for your purchase
Related manuals
Manual 36 pages 28.31 Kb

46 specifications

Wayne-Dalton 46 is a prominent garage door model known for its unique combination of durability, aesthetic appeal, and advanced technology. Designed specifically for residential properties, this door offers homeowners an array of features that enhance the overall functionality and style of their garages.

One of the standout characteristics of the Wayne-Dalton 46 is its construction. Made with high-quality materials, these doors are crafted to withstand various weather conditions. They are built using a steel frame, which provides structural integrity and support, while the insulated core helps to maintain energy efficiency in the home. The insulation also minimizes noise from outside, creating a peaceful environment within the garage.

In terms of style, the Wayne-Dalton 46 offers multiple design options to suit different architectural preferences. Homeowners can choose from various panel styles and colors, allowing for customization that complements the exterior of their homes. The door can be finished with a smooth or textured surface, adding to its visual appeal. Additionally, the Wayne-Dalton 46 features decorative hardware options, providing a touch of elegance and sophistication.

Technological innovation is another key aspect of the Wayne-Dalton 46. Equipped with the latest in garage door technology, these doors come with advanced safety features, including pinch-resistant construction, which helps to prevent injuries during operation. The door’s reliable opening mechanism ensures smooth and quiet operation.

Wayne-Dalton also incorporates smart technology into the 46 model. Homeowners have the option to equip their garage doors with Wi-Fi connectivity, allowing them to control the door remotely via smartphone apps. This feature adds convenience and security, enabling users to monitor their garage door's status and receive alerts in real time.

Maintenance of the Wayne-Dalton 46 is straightforward, thanks to its durable finish, which resists rust and corrosion. Regular inspections and basic upkeep will ensure longevity, providing a reliable garage door solution for years to come.

Overall, the Wayne-Dalton 46 stands out in the market for its impressive blend of style, durability, advanced features, and safety technology, making it an excellent choice for homeowners looking to enhance the appeal and functionality of their garages.
Top Page Image Contents