Wayne-Dalton 46 installation instructions Painting, Cleaning Your Garage Door

Page 36

�Cleaning

Cleaning Your Garage Door

IMPORTANT: DO NOT USE A PRESSURE WASHER ON YOUR GARAGE DOOR!

While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time. Slight chalking may also occur as a result of direct exposure to sunlight.

Cleaning the door will generally restore the appearance of the finish. To maintain an aesthetically pleasing finish of the garage door, a periodic washing of the garage door is recommended.

The following cleaning solution is recommended

A mild detergent solution consisting of one cup detergent (with less than 0.5% phosphate) dissolved into five gallons of warm water will aid in the removal of most dirt.

NOTE: The use of detergents containing greater than 0.5% phosphate is not recommended for use in general cleaning of garage doors.

NOTE: Be sure to clean behind weather stripping on both sides and top of door.

CAUTION: NEVER MIX CLEANSERS OR DETERGENTS WITH BLEACH.

GLASS CLEANING INSTRUCTIONS

Clean with a mild detergent solution (same as above) and a soft cloth. After cleaning, rinse thoroughly.

ACRYLIC CLEANING INSTRUCTIONS

Clean acrylic glazing with nonabrasive soap or detergent and plenty of water. Use your bare hands to feel and dislodge any caked on particles. A soft, grit-free cloth, sponge or chamois may be used to wipe the surface. Do not use hard or rough cloths that will scratch the acrylic glazing. Dry glazing with a clean damp chamois.

NOTE: DO NOT USE any window cleaning fluids, scouring compounds, gritty cloths or solvent-based cleaners of any kind.

�Painting

Surface Preparation for Painting

Wax on the surface must be removed or paint peeling/flaking will result. To remove this wax, it will be necessary to lightly scuff the surface with a fine steel wool pad, saturated with soapy water. A final wipe and rinse should be done with clean water only, to remove any loose particles and any soapy film residue.

Surface scratches, which have not exposed the metal substrate, can be lightly buffed or sanded with 0000 steel wool or No. 400 sand paper to create a smoother surface. Care must be taken to not expose the substrate under the paint. Once the substrate is exposed, the likelihood for rusting is greatly increased.

If substrate is exposed, it must be treated to prevent rust from forming. Sand the exposed area lightly and paint with a high quality metal primer, specifically intended for galvanized surfaces, to protect the area from corrosion. Allow for drying time on primer can label before applying topcoat. The surface of the factory-applied finish, that is being painted, must not be too smooth, or the paint will not adhere to it. It is advisable to test in an inconspicuous area, to evaluate adhesion. If poor adhesion is observed, surface preparation for painting the factory-applied finish must be repeated until desired results are achieved. Again, care must be taken to not expose the substrate under the paint.

Painting

After surface has been properly prepared, it must be allowed to dry thoroughly, and then coated immediately with premium quality latex house paint. Follow paint label directions explicitly. Oil base or solvent base paints are not recommended. Please note that if substrate is exposed and not properly primed, painting with latex paint may cause accelerated rusting of the steel in the exposed area.

NOTES:

1.Repainting of finish painted steel doors cannot be warranted, as this condition is totally beyond the door manufacturer’s control.

2.Consult a professional coatings contractor if in doubt about any of the above directions.

3. Follow directions explicitly on the paint container labels for proper applications of coatings and disposal of containers. Pay particular attention to acceptable weather and temperature conditions in which to paint.

36

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Series, Model Portland Source PlantTable of Contents Package Contents Package Contents Door Section IdentificationTools Required Torsion Spring Removal For Standard Lift Failure to use approvedWinding bars can cause spring Door agency release the tensionTorqueMaster Spring Removal Assembly off the flagangles and out Either direction. If the counterbalanceLeft hand side Applications, repeat for left hand sideExtension Spring Removal Removing the Old DoorPreparing the Opening Failure toSecurely attach a Suitable mounting pad to structurallyAttaching Fully Adjustable Flagangle to Vertical TrackInstalling Fully Adjustable Jamb BracketsBottom Bracket Drums Left handCounterbalance Roller Hinge tubeHinges Top Bracket Step PlateInstallation on the Top Section Installation on all otherAbove top bracket and secure with All glazed doors starting at 14’0 widthLift Handle Bottom SectionVertical Track Stacking SectionsTop Section Adjusting Top Brackets Horizontal TrackTorqueMaster Spring Tube Center Bracket BushingIdrive Installation Plug the motor power cord into OpenerOpener back and forth slightly to help Aid alignmentCable Drum Installation Drive Gear Installation End BracketsCounter Installation Securing Center Bracket BushingPositioning Support Bracket Mounting Disconnect Handle BracketAttaching Disconnect Handle Disconnect handle bracket. TightenHandle until snug, and then tighten Secure disconnect cable toCable Adjustments Securing DoorFor Spring Winding Ing adjustments to Setting Spring TensionWinding Bolt Rotation Prior to winding or makDrum Wrap Installation Rear SupportKeep horizontal track Parallel and within 3/4Installation Instructions Otherwise, the spring fittingsMay release from spring If not wound in the properSide Lock Pull Rope Trolley Operator Cleaning Cleaning Your Garage DoorPainting Limited Warranty Models 8000, 8100, 8200 Thank you for your purchase
Related manuals
Manual 36 pages 28.31 Kb

46 specifications

Wayne-Dalton 46 is a prominent garage door model known for its unique combination of durability, aesthetic appeal, and advanced technology. Designed specifically for residential properties, this door offers homeowners an array of features that enhance the overall functionality and style of their garages.

One of the standout characteristics of the Wayne-Dalton 46 is its construction. Made with high-quality materials, these doors are crafted to withstand various weather conditions. They are built using a steel frame, which provides structural integrity and support, while the insulated core helps to maintain energy efficiency in the home. The insulation also minimizes noise from outside, creating a peaceful environment within the garage.

In terms of style, the Wayne-Dalton 46 offers multiple design options to suit different architectural preferences. Homeowners can choose from various panel styles and colors, allowing for customization that complements the exterior of their homes. The door can be finished with a smooth or textured surface, adding to its visual appeal. Additionally, the Wayne-Dalton 46 features decorative hardware options, providing a touch of elegance and sophistication.

Technological innovation is another key aspect of the Wayne-Dalton 46. Equipped with the latest in garage door technology, these doors come with advanced safety features, including pinch-resistant construction, which helps to prevent injuries during operation. The door’s reliable opening mechanism ensures smooth and quiet operation.

Wayne-Dalton also incorporates smart technology into the 46 model. Homeowners have the option to equip their garage doors with Wi-Fi connectivity, allowing them to control the door remotely via smartphone apps. This feature adds convenience and security, enabling users to monitor their garage door's status and receive alerts in real time.

Maintenance of the Wayne-Dalton 46 is straightforward, thanks to its durable finish, which resists rust and corrosion. Regular inspections and basic upkeep will ensure longevity, providing a reliable garage door solution for years to come.

Overall, the Wayne-Dalton 46 stands out in the market for its impressive blend of style, durability, advanced features, and safety technology, making it an excellent choice for homeowners looking to enhance the appeal and functionality of their garages.
Top Page Image Contents