Wayne-Dalton 46 Installation Instructions, Otherwise, the spring fittings, Severe or fatal injury

Page 32

 

Rear Support Continued...

 

 

 

horizontal tracks to the rear supports with

Sound Framing Members

 

Tools Needed:

 

 

5/16”-18 x 1-1/4” hex head bolts and nuts

 

 

 

(may not be supplied). Horizontal tracks

 

 

 

must be level and parallel with door.

 

 

 

NOTE: If rear supports are to be installed

 

PERFERATED ANGLE -

 

over drywall, use 5/16” x 2” hex head lag

PERFERATED

 

screws.

BRACE

BOLTED USING

 

NOTE: If an idrive® opener will be

 

(2) 5/16” X 1-5/8” HEX

 

installed, position horizontal tracks one

 

HEAD LAG SCREWS TO

 

hole above level when securing it to rear

 

CEILING MEMBER AND

 

supports.

 

PARALLEL TO WIDTH OF

 

Adjust weather seal (if necessary). Now

 

DOOR

 

permanently attach the weather seal to

 

 

 

both door jambs and header. (Temporarily

HORIZONTAL TRACK

BOLT MUST EXTEND INTO

 

attached in PREPARING THE OPENING on

 

 

THE TRACK TO SERVE AS

 

page 10.) Avoid pushing weather seal too

 

 

 

A ROLLER STOP

 

tightly against face of door.

 

 

WARNING

Sound Framing Members

 

 

Prior to winding or making

 

 

 

adjustments to the springs,

 

 

 

ensure you’re winding in the

 

 

 

proper direction as stated in

ANGLE

 

 

the Installation Instructions.

PERFERATED ANGLE -

 

Otherwise, the spring fittings

BRACE

BOLTED USING

 

may release from spring

(2) 5/16” X 1-5/8” HEX

 

 

 

if not wound in the proper

 

HEAD LAG SCREWS TO

 

direction and could result in

 

CEILING MEMBER AND

 

severe or fatal injury.

 

PARALLEL TO WIDTH OF

 

Now, lift door and check it’s balance.

 

DOOR

 

Adjust, if door lifts by itself (hard to pull

 

 

 

down) or if door is difficult to lift (easy to

HORIZONTAL TRACK

BOLT MUST EXTEND INTO

 

pull down). Anytime spring adjustments

 

THE TRACK TO SERVE AS

 

are made you must loosen the lock nuts

 

 

 

A ROLLER STOP

 

to begin with and retighten both lock nuts

 

 

 

 

 

afterwards. To adjust spring(s), only add or

PERFORATED ANGLE

 

 

remove 1/4 turn on the counter at a time.

 

 

 

Adjust both sides equally.

 

 

 

IMPORTANT: Do not add or remove

 

 

 

more than 1 spring turn from

 

weather

 

specified amount. If the door still

 

 

does not operate easily, lower

 

seal

 

the door into the closed position,

 

 

 

UNWIND SPRING(S) TO ZERO, and

 

 

 

recheck the following items:

 

 

 

1. Check the door for level.

 

jamb

 

2. Check the TorqueMaster® Spring

 

 

 

 

 

Tube and flagangles for level and

(3) 5/16”

 

 

plumb.

 

 

BOLTS & NUTS

permanently attached

 

3. Check the distance between the

 

flagangles - must be door width

 

weather seal

 

plus 3-3/8” to 3-1/2”.

 

 

 

4. Check the counterbalance cables

 

 

 

for equal tension - adjust if

 

 

 

necessary.

 

 

 

5. Rewind the spring(s).

 

 

 

6. Make sure door isn’t rubbing on

 

 

 

jambs.

 

 

 

NOTE: As a safety feature, the right hand

 

 

 

end bracket cannot be disassembled

 

 

 

for service until the spring is completely

 

 

 

unwound and the counter cover reads

 

 

 

zero.

 

 

 

After door installation is completed, refer

 

 

 

to the idrive® owner’s manual.

 

 

32

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Series, Model Portland Source PlantTable of Contents Package Contents Package Contents Door Section IdentificationTools Required Torsion Spring Removal For Standard Lift Failure to use approvedWinding bars can cause spring Door agency release the tensionTorqueMaster Spring Removal Assembly off the flagangles and out Either direction. If the counterbalanceLeft hand side Applications, repeat for left hand sideExtension Spring Removal Removing the Old DoorPreparing the Opening Failure toSecurely attach a Suitable mounting pad to structurallyAttaching Fully Adjustable Flagangle to Vertical TrackBottom Bracket Installing Fully Adjustable JambBrackets Drums Left handCounterbalance Roller Hinge tubeHinges Top Bracket Step PlateInstallation on the Top Section Installation on all otherAbove top bracket and secure with All glazed doors starting at 14’0 widthLift Handle Bottom SectionVertical Track Stacking SectionsTop Section Adjusting Top Brackets Horizontal TrackTorqueMaster Spring Tube Center Bracket BushingIdrive Installation Plug the motor power cord into OpenerOpener back and forth slightly to help Aid alignmentCable Drum Installation Drive Gear Installation End BracketsCounter Installation Securing Center Bracket BushingPositioning Support Bracket Mounting Disconnect Handle BracketAttaching Disconnect Handle Disconnect handle bracket. TightenHandle until snug, and then tighten Secure disconnect cable toFor Spring Winding Cable AdjustmentsSecuring Door Ing adjustments to Setting Spring TensionWinding Bolt Rotation Prior to winding or makDrum Wrap Installation Rear SupportKeep horizontal track Parallel and within 3/4Installation Instructions Otherwise, the spring fittingsMay release from spring If not wound in the properSide Lock Pull Rope Trolley Operator Painting CleaningCleaning Your Garage Door Limited Warranty Models 8000, 8100, 8200 Thank you for your purchase
Related manuals
Manual 36 pages 28.31 Kb

46 specifications

Wayne-Dalton 46 is a prominent garage door model known for its unique combination of durability, aesthetic appeal, and advanced technology. Designed specifically for residential properties, this door offers homeowners an array of features that enhance the overall functionality and style of their garages.

One of the standout characteristics of the Wayne-Dalton 46 is its construction. Made with high-quality materials, these doors are crafted to withstand various weather conditions. They are built using a steel frame, which provides structural integrity and support, while the insulated core helps to maintain energy efficiency in the home. The insulation also minimizes noise from outside, creating a peaceful environment within the garage.

In terms of style, the Wayne-Dalton 46 offers multiple design options to suit different architectural preferences. Homeowners can choose from various panel styles and colors, allowing for customization that complements the exterior of their homes. The door can be finished with a smooth or textured surface, adding to its visual appeal. Additionally, the Wayne-Dalton 46 features decorative hardware options, providing a touch of elegance and sophistication.

Technological innovation is another key aspect of the Wayne-Dalton 46. Equipped with the latest in garage door technology, these doors come with advanced safety features, including pinch-resistant construction, which helps to prevent injuries during operation. The door’s reliable opening mechanism ensures smooth and quiet operation.

Wayne-Dalton also incorporates smart technology into the 46 model. Homeowners have the option to equip their garage doors with Wi-Fi connectivity, allowing them to control the door remotely via smartphone apps. This feature adds convenience and security, enabling users to monitor their garage door's status and receive alerts in real time.

Maintenance of the Wayne-Dalton 46 is straightforward, thanks to its durable finish, which resists rust and corrosion. Regular inspections and basic upkeep will ensure longevity, providing a reliable garage door solution for years to come.

Overall, the Wayne-Dalton 46 stands out in the market for its impressive blend of style, durability, advanced features, and safety technology, making it an excellent choice for homeowners looking to enhance the appeal and functionality of their garages.
Top Page Image Contents