Emerson UVC120, MAN -0016-00 manual Special Function Menu, Error Check Mode Err Chc

Page 34

SELECT/RESET switch to choose the selection. To exit the main menu without choosing an option, toggle through the selections until ‘rtn’ is shown on the lower display.

ERROR CHECK MODE (Err Chc)

This is the first selection in the main menu. Enter the main menu and activate the SELECT/RESET switch when ‘Chc’ is shown on the left side of the display and ‘Err’ is shown on the right side of the display ‘dsP’ will be shown on the left side of the display and ‘Err’ on the right side of the display. To see the errors activate the SELECT/RESET switch. The controller will display each error for approximately 5 seconds. Once all errors have been shown, ‘Clr’ will be shown on the left side of the display and ‘Err’ on the right side. Activate the SELECT/RESET switch to clear the errors and return to the normal operating mode.

If it is not necessary to see what errors have been logged, but only to clear them, activate the MENU/SET switch when ‘dsP’ ‘Err’ is shown. The ‘Clr’ ‘Err’ selection will be displayed. Activate the SELECT/RESET switch to clear the errors and return to the normal operating mode.

NOTE:

If no errors exist, this function is hidden and can not be accessed.

BYPASS MODE (bPS)

This is the second selection in the main menu. It is used for testing detector operation without activating alarm outputs. To enter this mode, first enter the main menu, toggle through the selections using the MENU/SET switch and activate the SELECT/RESET switch when ‘bPS’ is shown on the right side of the display ‘Ch' will be shown on the left side of the display and the UV seen by the detector is shown on the right side of the display in counts per second.

Activating the SELECT/RESET switch while a channel is in bypass will perform the manual vi test. A significant increase in the counts per second should be observed on the lower display.

A range between 150 and 400 cps is expected.

Activating the MENU/SET switch will toggle through all of the active channels and then show ‘test’ on the left side of the display and ‘bPS’ on the right side of the display. In this manual test mode, all alarm outputs are inhibited, but the faceplate indicators will operate as in the normal operating mode. If a flame occurs or UV test lamp is used to activate the detectors the faceplate indicators operate as in the normal operating mode, but the alarm outputs will not activate. To exit the bypass mode, activate the SELECT/RESET switch while ‘test bPS’ is displayed.

SPECIAL FUNCTION MENU

To enter the special function menu activate both switches simultaneously for 20 seconds, until ‘FoP’ is shown on the right side of the display. This menu is a little harder to enter because it is not intended for general use. The items in this menu are used for system maintenance and calibration of equipment.

FORCED CURRENT OUTPUT MODE (FoP)

The forced current output mode is used to check the current output calibration and the operation of any devices connected to the current outputs.

To enter the forced current output mode, enter the special function menu. W hen ‘FoP’ is shown on the right side of the display activate the SELECT/RESET switch. Upon successful entry into this mode the left side of the display will flash ‘gPn’. Activate the MENU/SET switch until the desired

- 28 -

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Ultraviolet Fire Detection System Page Page Page Table of Contents Unit V Maintenance Unit I General Information Detector Specifications Dimensions Basic Operation Controller Controller Faceplate Description Relay Outputs OutputsCurrent Outputs Automatic Diagnostics and Fault Identification External ResetProgramming Options System Application Unit II UV Fire DetectionDetector Petroleum Products HandlingGaseous Fuel Handling Detector Sensitivity Spectral Sensitivity RangeOther Processes Cone of Vision System SensitivityInstallation General Wiring Requirements Unit III System InstallationController Wiring Page W iring for U1F-UV with Non-Isolated Current Output W iring for U1F-UV with Isolated Current Output W iring for U2F-UV with Non-Isolated Output W iring Diagram for U2F-UV with Isolated Current Output W iring for U4F-UV with Non-Isolated Current Output W iring for U4F-UV with Isolated Current Output Position and Density of Detectors DIP Switch SettingsMounting the Detector U1F, U2F and U4F Controller Sensitivity AdjustmentChannel Selection U2F and U4FRelay Outputs ENERGIZED/DE-ENERGIZED Relay Outputs LATCHING/NON-LATCHINGExample Page Time Delay for Area Alarms Relay SettingsCheckout Procedure Startup ProcedureUnit IV System Operation Manual Check Procedure Alternate Test Procedure Normal Operation Fire ResponseCurrent Output Situation Main Menu Error Check Mode Err Chc Special Function MenuCurrent Calibration Mode CuC Troubleshooting Unit V MaintenanceRoutine Maintenance Device Repair and ReturnPage Appendices B lis h ed in Accordance with E1A Standard Appendix B Procedure For Activating Reed Switches Appendix C Record Of Dip Switch Settings Appendix D Common Ultra-Violet Absorbing Gases Appendix E Wire Resistance In Ohms AWG #20 AWG #18 AWG #16 AWG #14 AWG #12 AWG #10 AWG #8

0016-00, UVC120, MAN -0016-00 specifications

The Emerson MAN-0016-00, UVC120, 0016-00 is a state-of-the-art device designed to meet the demands of modern industrial and commercial applications. This advanced model showcases Emerson’s commitment to innovation, providing users with reliable performance and cutting-edge technology.

One of the key features of the Emerson MAN-0016-00 is its superior control capabilities. Equipped with sophisticated algorithms, this device ensures precise and adaptable control over various processes, improving efficiency and productivity in operations. Users benefit from enhanced responsiveness to changing conditions, allowing for quick adjustments that lead to optimized performance.

Another noteworthy technology integrated into the UVC120 is its advanced user interface. The device boasts a highly intuitive control panel that facilitates easy navigation and management of settings. This user-friendly design minimizes the learning curve for operators, ensuring that they can quickly familiarize themselves with its functions. The display provides clear, real-time feedback, enabling users to monitor system performance effortlessly.

The Emerson MAN-0016-00 is also characterized by its robust construction. Designed to endure harsh environmental conditions, this model is built with durable materials that enhance its longevity and reliability. It is resistant to various industrial contaminants, ensuring consistent operation even in challenging settings.

Energy efficiency is a hallmark of the UVC120 model. By employing innovative power management technologies, it significantly reduces energy consumption without compromising performance. This emphasis on sustainability not only lowers operational costs for users but also aligns with global efforts to minimize environmental impact.

Moreover, the Emerson MAN-0016-00 incorporates advanced safety features that prioritize user protection. These include integrated alarms and emergency shut-off mechanisms that respond to detected anomalies, enhancing overall workplace safety. The design also adheres to international safety standards, ensuring compliance and peace of mind for users.

In conclusion, the Emerson MAN-0016-00, UVC120, 0016-00 stands out as an exemplary model in the field of industrial technology. Its combination of precision control, user-friendly interface, robust construction, energy efficiency, and safety features make it an ideal choice for various applications. As industries continue to evolve, devices like this play a crucial role in enhancing performance, safety, and sustainability across the board.
Top Page Image Contents