Desa HD-9140 manual Troubleshooting Guide, Technical Service, Do Not Send Products

Page 12

Troubleshooting Guide

SYMPTOM	POSSIBLE CAUSE

Lights will	1.	Light switch is turned off.
not come	2.	Flood light is loose or burned out.
on.	3.	Fuse is blown or circuit breaker is
		turned off.
	4.	Daylight turnoff is in effect. (Re-
		check after dark).
	5.	Incorrect circuit wiring, if this is a
		new installation.
	6.	Re-aim the sensor to cover de-
		sired area.
Lights come	1.	Control may be installed in a rela-
on in		tively dark location.
daylight.	2.	Control is in Test. (Set control
		switch to an ON-TIME position).

Lights come	1.	Control may be sensing small ani-
on for no		mals or automobile traffic. (Re-
apparent		aim sensor or use lens shield).
reason.	2.	Sensitivity is set too high. (Reduce
		sensitivity. Turn Range Boost off).

SYMPTOM	POSSIBLE CAUSE

Lights stay	1.	A lamp is positioned too close to
on continu-		the sensor or pointed at objects
ously.		that causes the sensor to trigger.
		(Aim the lamp away from the sen-
		sor or objects).
	2.	Control is pointed at a heat source
		like an air vent, dryer vent, or brightly-
		painted heat-reflective surface. (Re-
		aim sensor. Turn Boost off).

Lights flash	1. Heat or light from the lamps may be
on and off.		turning the Light Control on and off.
		(Aim lamps away from the sensor.
		Turn Boost off).
	2.	Reflected heat from other objects
		are triggering the sensor. (Re-aim
		sensor. Turn Boost off).
	3.	Control is warming up. (Flashing is
		normal under these conditions. Wait
		1 minute for sensor to warm up).
	4.	Control is in Test. (Set control switch
		to an ON-TIME position).

Technical Service

(Do Not Send Products)

If you experience a problem, follow this guide. You may also want to visit our Web site at: www.desatech.com. If the problem persists, call* for assistance at 1-800-858-8501,7:30 AM to 4:30 PM CST (M-F). You may also write* to:

DESA Specialty Products™

P.O. Box 90004, Bowling Green, KY 42102-9004

*If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase.

No Service Parts Available for this Product

-12-	595-5660-06

Image 12

Contents Wide Angle Replacement Motion Sensor Contents Enhanced Performance Features IntroductionPackage Contents Additional Items NeededInstallation Standard WiringWall Mount Eave MountWiring to a Motion Light & Standard Fixture Specifications Finish MountingTest and Adjustment Turn on the circuit breaker and light switchAdjustments Expected CoverageMaximum Range Least SensitiveCoverage Angle Operation ManualTroubleshooting Guide Technical ServiceNo Service Parts Available for this Product Do Not Send ProductsLifetime Warranty 595-5660-06 Cambio DEL Detector DE Movimiento DE Angulo Grande Indice Introducción Características Mejoradas de RendimientoContenidos del Paquete Artículos adicionales que se NecesitanInstalación Cableado EstándarMontaje en pared Montaje en aleroConexión a la luz de movimento y al aparato estándar Fin del Montaje EspecificacionesPrueba y Ajuste Prenda el cortacircuitos y el interruptor de luzAlcance Máximo Lo menos sensibleDecida quŽ lado de la placa translœcida desea cubrir Angulo de Cobertura MáximaFuncionamiento Hasta el amanecerGuia de Investigacion de Averias Servicio TécnicoNo enviar los productos No hay piezas de servicio disponibles para este productoGarantía Permanente 595-5660-06 Détecteur DE Mouvement Grand Angle DE Remplacement Table des matières Page Contenu de l’emballage Articles additionnels requisCâblage standard Montage muralMontage sous avant-toit Une fois que vous avez dŽterminŽ les appareils Finir le montage Spécifications Test et réglage Test et réglage suite Coverture prévuePortée maximale Moins sensibleAngle de couverture Maximum Compltement au contact de la lentilleFonctionnement AutoService Technique Guide de dépannageNenvoyez pas de produits Aucune pièce de rechange n’est disponible pour ce produitGarantie à vie 595-5660-06