Bryant KNCGPP3RC manual Quick Set Up Guide, Setting up your alarm for first time operation

Page 4

Quick Set Up Guide

We urge you to read this entire manual

in the sequence it is presented.

Listed below are six easy steps for setting up your Bryant CO alarm. Please read this entire guide for complete information.

Setting up your alarm for first time operation:

Step 1

Determine the best location for your CO alarm(s). Usually

this is in or near bedrooms. The alarm should be located where it can wake you if it alarms at night. Refer to page 8 for installation location information.

Step 2

Your CO alarm is equipped to be mounted as a corded unit, a direct plug unit or a table top unit. In the “as shipped” configuration, the unit can be plugged directly into a wall socket. (If your outlets are mount- ed horizontally, please refer to page 11, “to rotate adapter”). If the transformer/adapter is taken out of the unit, the alarm can be mount- ed on the wall at eye level, while the transformer is plugged into a wall socket. The unit can also be set on a table if the support at the bottom of the unit is pulled out (see “rear view” illustration on page 10). Refer to pages 10-12 for further information on installing your alarm.

Step 3

A Bryant rechargeable battery pack is provided for backup in the event of a power outage. To install the battery pack, open the back door and align the connector with the slot in the battery. Insure the orientation of the two alignment ribs align with the slots in the battery case.

Press the connector in until it is fully seated. Depending on the charge state of the battery pack (the battery packs can have different amounts of energy stored in them due to storage time), you may hear the alarm sound briefly to indicate the alarm is receiving power. Place battery pack into battery compartment and replace back door (refer to page 13).

Note: Battery backup will be limited until the battery has fully charged. It may take up to 24 hours for the battery back up to fully charge.

Step 4

Plug the alarm into a standard, unswitched 120 volt AC electric outlet in one of the configurations listed in step 2.

1

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Carbon Monoxide Table of Contents Page Quick Set Up Guide Setting up your alarm for first time operationQuick Set Up Guide Introduction Features Bryant CO Alarm front viewDigital Display Rear view with back door removed Pull-Out Transformer/AdapterWhat Carbon Monoxide Alarms Can and Cannot Do Where to Install Your CO Alarm InstallationRecommended Locations Where Not to Install Your CO Alarm AT Least 5 feet away from applianceHow to Install Your Alarm Direct Plug AlarmTo install Avoid the followingWall Mounted Alarm Plug the alarm into an unswitched wall socketIf the outlet is mounted horizontally sideways To rotate the adapterTable Top Alarm WallBattery Installation Battery Installation and OperationBattery Backup Operation Battery Backup OperationBattery Back-up Operation in Low Battery Lb Condition Battery Back-up Operation inTrouble Alarm ConditionPage Normal Operating Characteristics OperationTesting the Electronics If the alarm malfunctions Malfunction Signal Group 1 Component FailureMalfunction Signal Group 2 Microprocessor Failure What to do if you’re not sureAlarm from the electrical outlet before vacuuming How to Care for Your AlarmStart and some cleaning agents To Reset the Peak Level Memory… Peak Level MemoryHome Safety Tips What You Can Do Carbon MonoxideWhat You Should Not Do Never use a gas range, oven, or clothes dryer for heatingClues You Cannot See Loose or disconnected vent/chimney, fireplace or applianceUnderstand the Effects of Carbon Monoxide Exposure What To Do When the Alarm Sounds Common Mild Exposure SymptomsCommon Medium Exposure Symptoms Common Extreme Exposure SymptomsCall your emergency services If alarm signal sounds 4 quick chirps, 5 seconds offTion Specifications How the Unit Determines When to Alarm SpecificationsReplacement of Alarm AC and DC Start Up, Alarm and Error Operation Display ReadingsAC Powered in Normal Stand-by Operation DC Powered in Battery Backup OperationLi-Ion Battery Handling Precautions Detect COBattery Storage When Detached From the Alarm Limited Warranty For Warranty Service Please send products and all other correspondence to
Top Page Image Contents