Heat & Glo LifeStyle PIER-36TR-IPI, PIER-36TRLP-IPI, ST-36TRLP-IPI Maintenance and Service

Page 13

3 Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.

When properly maintained, your fireplace will give you many years of trouble-free service. We recommend an- nual service by a qualified service technician.

Doors, Surrounds, Fronts

Frequency: Annually

By: Homeowner

Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualified service technician only. The fireplace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service ap- pointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the fireplace must be kept clean.

CAUTION! Risk of Burns! The fireplace should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally

By: Homeowner

Tools Needed: Protective gloves, glass cleaner, drop cloth and a stable work surface.

CAUTION! Handle fixed glass assembly with care. Glass is breakable.

•Avoid striking, scratching or slamming glass

•Avoid abrasive cleaners

•DO NOT clean glass while it is hot

•Prepare a work area large enough to accommodate fixed glass assembly and door frame by placing a drop cloth on a flat, stable surface.

Note: Fixed glass assembly and gasketing may have res- idue that can stain carpeting or floor surfaces.

•Remove door or decorative front from fireplace and set aside on work surface.

•See Section 14.G for instructions to remove fixed glass assembly.

•Clean glass with a non-abrasive commercially available cleaner.

-Light deposits: Use a soft cloth with soap and water

-Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer)

•Carefully set fixed glass assembly in place on fireplace. Hold glass in place with one hand and secure glass latches with the other hand.

•Reinstall door or decorative front.

•Inspect for scratches, dents or other damage and repair as necessary.

•Check that louvers are not blocked.

•Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally

By: Homeowner

Tools needed: Replacement batteries and remote con- trol instructions.

•Locate remote control transmitter and receiver.

•Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

•Place batteries as needed in remote transmitters and battery-powered receivers.

•Place remote control out of reach of children.

If not using your fireplace for an extended period of time (summer months, vacations/trips, etc), to prevent unin- tended operation:

•Remove batteries from remote controls.

•Unplug 3 volt adapter plug on IPI models.

Venting

Frequency: Seasonally

By: Homeowner

Tools needed: Protective gloves and safety glasses.

•Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

•Verify termination cap clearance to subsequent construc- tion (building additions, decks, fences, or sheds). See Section 6.

•Inspect for corrosion or separation.

•Verify weather stripping, sealing and flashing remains intact.

•Inspect draft shield to verify it is not damaged or missing.

Heat & Glo • ST-36TR-IPI, PIER-36TR-IPI • 2176-900 Rev. F • 8/11

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents What to do if you smell gas ModelsHomeowner Reference Information CongratulationsUser Guide Table of ContentsTroubleshooting Appliance SetupFinishing Reference MaterialsLimited Lifetime Warranty  B. Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsOperating Instructions User Guide Gas Fireplace SafetyYour Fireplace Fixed Glass Assembly Blower InstallationRemote Controls, Wall Controls and Wall Switches Blower Kit optionalFinal inspection by Lighting Instructions IPIAfter Fireplace is Lit Frequently Asked QuestionsMaintenance and Service Maintenance Tasks-Qualified Service Technician Ember Light ReplacementGasket Seal and Glass Assembly Inspection LogsIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChasePIER-36TR-IPI Pier Combustible Mantel Mantel and Wall Projections See-Through Combustible MantelSee-Through Non-Combustible Mantel Pier Non-Combustible MantelTOP View Vent Termination Minimum Clearances Termination LocationsCovered Alcove Applications = AIR Supply Inlet = Area Where Terminal is not PermittedTo Install the Heat Shield Install Support BracketsContinue Adding Vent Components Approved Pipe Vent Information and DiagramsVent Table Key Use of ElbowsTo SLP series vent pipe, if desired Vent DiagramsTop Vent Horizontal Termination V1 Minimum H1 Maximum Top Vent Horizontal Termination One Elbow Two ElbowsMinimum + H 2 Maximum Top Vent Horizontal Termination Three Elbows Exhaust restrictor Instructions Break Here Maximum + V 2 Minimum Two Elbows Three ElbowsPage H1 Maximum V1 Minimum H2 Maximum H1+ H2 Maximum Rear Vent Horizontal Termination Two ElbowsMinimum + H 2 Maximum Rear Vent Vertical Termination One ElbowH1 Maximum V1 Minimum H1+ H2 Maximum Rear Vent Vertical Termination Three ElbowsPipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall PenetrationPipe DVP SLP Vertical Penetration FramingFlat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Top Vent Appliance PreparationProceed to . C Cut the metal retaining band Rear VentSecuring An Appliance Securing and Leveling the ApplianceAttach Vent to the Firebox Assembly Installing Vent Pipe DVP and SLP PipeAssemble Vent Sections DVP Pipe Only Assemble Pipe Sections DVP Pipe OnlyAssemble Slip Sections Assemble Vent Sections SLP Pipe OnlyDisassemble Vent Sections Secure the Vent SectionsInstall Decorative Ceiling Components SLP only Assemble and Install Storm Collar Install Metal Roof FlashingInstall Decorative Wall Components SLP only Install Vertical Termination CapHeat Shield Requirements for Horizontal Termination DVP-HPC1 DVP-HPC2 Install Horizontal Termination Cap DVP and SLP PipeFuel Conversion Gas InformationGas Pressure Gas ConnectionJunction Box Installation Wiring RequirementsIntelliFire Ignition System Wiring Electrical Service and RepairPrecautions WSK-MLT Multifunction Wall SwitchWiring the Wall Switch Connect the Temperature Sensor Switch for Fan optional Install the Flame SolenoidWall Switch Button Operation Setting Flame Height/Manifold PressureWSK-MLT Operating Instructions Up and Down Arrows Finishing To install the Splatter GuardSplatter Guard To Remove the Splatter Guard To Close the Lower Access Panel12 Minimum Vertical and Maximum Horizontal Facing Material 17 Noncombustible Facing DiagramST-36TR-IPI Finishing Material22 Pier Door Finishing Elevated Hearth Systems Appliance Setup Placing the Ember Material Placement of EmbersInch Install the Log Assembly5 4 Notch engaged with grate tine NotchAir Shutter Setting Install Trim Kits and SurroundsSymptom Possible Cause Corrective Action TroubleshootingIntelliFire Ignition System Sure specifications. Polish flame-sensing rod with fine steel Reference Materials Appliance Dimension DiagramElectrical Access GAS Line Left View Front View Right View DVP-AS2 Vent Components DiagramsDVP-TRAP1 DVP-TRAP2 DVP-TRAPK1 DVP-TRAPK2 DVP-HPC1 DVP-HPC2 RF6M RF12M DVP-TV DVP-HRC-SS Optional Wire Harness660 mm ElbowExtended Heat Shield Ceiling FirestopWall Thimble-Black Black Support Box-BlackAdapter Log Set Assembly Service PartsAt Depot See-Through Gas FireplacePier Direct Vent Fireplace StockedPIER-36TR, ST-36TR-IPI #17 Valve AssemblyST-36TR-IPI, PIER-36TR-IPI Service Parts ListContact Information

PIER-36TR-IPI, PIER-36TRLP-IPI, ST-36TRLP-IPI, ST-36TR-IPI specifications

Heat & Glo is renowned for its innovative and stylish fireplace solutions, and their LifeStyle series is no exception. The LifeStyle models, including the PIER-36TRLP-IPI, PIER-36TR-IPI, ST-36TRLP-IPI, and ST-36TR-IPI, are designed to provide both aesthetic appeal and unparalleled heating performance, making them perfect for a variety of living spaces.

One of the defining features of these units is their contemporary design, which integrates seamlessly into modern interiors. The sleek, linear appearance allows for versatile installation options, whether in a wall or as a standalone feature. With a focus on maximizing visual impact, the large glass viewing area provides an unobstructed view of the flames, creating an inviting ambiance.

In terms of technology, these fireplaces are equipped with advanced ignition systems, specifically the IntelliFire® ignition system, which intelligently manages flame levels and optimizes efficiency. This technology not only aids in ease of use but also enhances safety, reducing the risk of unintended ignition.

The LifeStyle series also emphasizes energy efficiency. With an emphasis on reducing environmental impact, these fireplaces boast high efficiency ratings, ensuring that homeowners enjoy warmth without excessive energy consumption. The incorporation of direct vent technology allows for better heat retention indoors while drawing in fresh air from outside, minimizing drafts.

When it comes to performance, the LifeStyle models deliver reliable heating capabilities. Each unit is capable of producing up to 36,000 BTUs, ensuring sufficient warmth for medium to large spaces. This output, combined with adjustable flame height and ember bed options, allows users to customize their heating experience according to personal preferences.

Another characteristic of the LifeStyle series is the extensive range of aesthetically pleasing decorative options. Owners can select from various media, such as glass or ceramic logs, which add a touch of style to the fireplace while complementing the overall decor of the room.

Finally, easy maintenance is a hallmark of the LifeStyle series. Many components are designed for straightforward accessibility, making routine upkeep simple and hassle-free. This attention to practicality ensures that homeowners can enjoy their fireplace without the burden of complicated maintenance routines.

In summary, the Heat & Glo LifeStyle PIER and ST series combines elegant design, advanced technology, and efficient heating, making them a sought-after choice for homeowners looking to enhance their living spaces with a modern fireplace solution.
Top Page Image Contents