Infinity Comprehensive Field Service Guide for Heating Plates
Page 22

FIELD SERVICE

REPLACEMENT OF HEATING PLATES

REPLACEMENT PART NUMBERS

 

 

115V

M (Set of 2)

33915

L

 

 

Set of 2

Side Plates

33918

Set of 2

Rear Plates

33917

 

 

 

1.Remove the back panel of the furnace.

2.Remove the nuts which hold the heating plate wires to the power terminals and straighten the heating plate wires (Figure 4).

3.Open the furnace door and find the two ceramic sections at the front of the furnace chamber. Hold the furnace door partially open while removing the ceramic sections. They are not readily removed when the door is fully open. Remove the right-hand ceramic section by lifting it upward until the bottom of the section clears the sheet metal housing. Pull the bottom of the ceramic section out, then pull it down so the upper half clears the sheet metal housing. Remove the left-hand ceramic plate in the same way.

4.Remove the floor plate, then carefully slide the two side heating plates out the front of the furnace. The two rear heating plates on Infinity L may now be removed.

5.Check the condition of the filler strip insulation in the space to the left and right of the ceramic front sections. Replace if required*.

6.Check the condition of the floor plate which provides insulation and serves as a spacer between the bottom ends of the heating plates. Replace if required*.

7.To install the new heating plates reverse the procedure. Push the ceramic heating plates back into place on the rear insulating panel. When reconnecting the heating plate wires at the rear of the furnace, be sure to replace all hardware in its original position. (Figure 4.) Tighten all connections.

*Replacement Part: Floor Plate w/ Filler Strip Insulation Infinity M: PN 33980; Infinity L: PN33981

21

Page 21 Page 23
Image 22
Page 21 Page 23
Contents F i n i t y TM Table of Contents Do Not Attempt Internal Service WarrantySafety Instructions IntroductionInfinity M Infinity L SpecificationsInfinity M and L Display KEY Parts Identification and ExplanationFront Panel Figure DescriptionInfinity M and L Identification Display Description Lower Back Panel FigureInfinity Lower Back Panel Unpack and SET-UP InstallationVenting Instructions To Turn the Beep on and OFF Figure Operation Program and Operate ONE Stage Program FigureProgram and Operate TWO Stage Program Figure Program and Operate Three Stage Program Figure Program and Operate Four Stage Program Figure Review a Program Figure Edit While a Program is Running Figure While the program is runningHold Time Sample ONE Stage ProgramNight Time Heat Rate StageSample Three Stage Program Program with Cooling Error Codes Error Description Probable Cause CodeError Codes Temperature Calibration ServiceCleaning Instructions Temperature Calibration with Calibration Tablets FigurePower Failure Replacement of Door Insulation and SpringsField Service Replacement of Heating PlatesInfinity with Upper Rear Panel Removed Infinity MReplacement of the Main PC Board 115VPage Replacement of the Thermocouple Assembly PN Replacement of the Triac PN Spare Parts List Parts for Infinity M DescriptionParts for Infinity L Description Program # Metals Program Card FormsHeat Temp Hold Rate Time Stage Program Card Forms Toll Free 1-800-JELRUS-1

M30, L30 specifications

The Infinity L30 and M30 are two notable offerings from Infinity, a company renowned for its commitment to high-quality audio technology and innovative designs. These speakers are designed to cater to audiophiles and enthusiasts alike, providing an immersive listening experience.

The Infinity L30 is a floor-standing speaker that emphasizes powerful sound and a stylish form factor. One of its key features is the incorporation of Infinity’s proprietary EMIT (Electromagnetic Induction Tweeter) technology. This technology is known for delivering exceptionally clear high frequencies, allowing listeners to experience the finer details in their music. The L30 also features a robust bass reflex design, which enhances low-frequency response, resulting in a richer sound experience. The speaker's design typically includes a high-quality, wooden cabinet that helps to minimize unwanted vibrations while adding an aesthetic appeal to any room.

On the other hand, the Infinity M30 is a bookshelf speaker designed for more compact environments without compromising sound quality. It shares several technologies with the L30, including the EMIT tweeter, ensuring that high-frequency reproduction remains clear and detailed. The M30's design also includes a rear-firing bass port, which helps to improve the bass response, making it suitable for a variety of setups, whether they are part of a home theater system or a dedicated stereo setup. The speaker is designed for versatility, easily fitting into various decor styles while delivering impressive sound quality.

Both speakers benefit from Infinity’s meticulous engineering, ensuring that they provide an exceptional audio experience. Features such as high-efficiency drivers, a wide frequency range, and the inclusion of durable materials contribute to their performance and longevity. Users can expect these speakers to produce sound with great accuracy and depth, making them ideal for genres ranging from classical to modern pop.

In summary, the Infinity L30 and M30 are exemplary models that showcase Infinity’s dedication to producing high-performance audio solutions. With advanced technologies, such as the EMIT tweeters, and thought-out designs aimed at maximizing sound quality, both models make powerful additions to any audio setup, promising to elevate the listening experience for users. Whether for music or movies, the L30 and M30 are sure to impress with their sonic capabilities and visual appeal.
Top Page Image Contents