Infinity L30, M30 manual Installation, Unpack and SET-UP, Venting Instructions

Page 8

INSTALLATION

UNPACK AND SET-UP

1.Unpack the contents of the box. Remove the following materials:

A.Vent Tube - Remove from bubble wrap and insert in hole on top of furnace.

B.Calibration Table Kit - Remove plastic bag containing two tablets and save for future use.

C.Burnout Tray - Remove tray(s) from bubble wrap and install on the floor of the chamber.

2.Place the furnace in position allowing a minimum of 10 inches (25.4 cm) of air space on all sides.

3.Plug the power cord into a wall receptacle. First connect the power cord located on the rear of the furnace. For large furnaces a dedicated 20A, 115V circuit terminated with a NEMA 5-20 R type receptical is required. For medium furnaces a dedicated 15A, 115V curcuit terminated with a NEMA 5-15 R type receptical is the minimum requirement. A 20 AMP circuit is recommemnded.

4.The furnace is now ready for operation.

CAUTIONS:

DO NOT BLOCK VENT HOLE ON TOP OF THE FURNACE. Hot gases are vented through this hole.

TO SET TEMPERATURE SCALE (Figure 1)

115V furnaces are pre-set in degrees Fahrenheit.

1.Turn the power switch on. (If the furnace is already on, be sure it is in the idle mode - no program is running.) The chamber temperature appears on the Main Display and the °F light goes on.

2. Press

at the same time. The degree light switches to the opposite temperature scale.

VENTING INSTRUCTIONS

Vent fans must have a minimum capacity of 100 cubic feet per minute for each burn out furnace.

If a common hood is used for more than one burn out furnace, fan capacity must be 100 cubic feet per minute for each square foot of hood opening.

All hoods, vent pipe and ducting components must be constructed of non combustable materials and be installed in accordance with local building codes.

Maximum expected exhaust temperature is 1800°F (980°C).

Maximum expected exhaust waste heat is 5,100 BTU’S / Hour or 1,000 Watts.

7

Page 7 Page 9
Image 8
Page 7 Page 9
Contents F i n i t y TM Table of Contents Warranty Safety InstructionsDo Not Attempt Internal Service IntroductionInfinity M and L SpecificationsInfinity M Infinity L KEY Parts Identification and Explanation Front Panel FigureDisplay DescriptionInfinity M and L Identification Infinity Lower Back Panel Lower Back Panel FigureDisplay Description Venting Instructions InstallationUnpack and SET-UP To Turn the Beep on and OFF Figure Operation Program and Operate ONE Stage Program FigureProgram and Operate TWO Stage Program Figure Program and Operate Three Stage Program Figure Program and Operate Four Stage Program Figure Review a Program Figure Edit While a Program is Running Figure While the program is runningSample ONE Stage Program Night Time Heat RateHold Time StageSample Three Stage Program Program with Cooling Error Codes Error Description Probable Cause CodeError Codes Service Cleaning InstructionsTemperature Calibration Temperature Calibration with Calibration Tablets FigurePower Failure Replacement of Door Insulation and SpringsField Service Replacement of Heating PlatesInfinity with Upper Rear Panel Removed Infinity MReplacement of the Main PC Board 115VPage Replacement of the Thermocouple Assembly PN Replacement of the Triac PN Spare Parts List Parts for Infinity M DescriptionParts for Infinity L Description Heat Temp Hold Rate Time Stage Program Card FormsProgram # Metals Program Card Forms Toll Free 1-800-JELRUS-1

M30, L30 specifications

The Infinity L30 and M30 are two notable offerings from Infinity, a company renowned for its commitment to high-quality audio technology and innovative designs. These speakers are designed to cater to audiophiles and enthusiasts alike, providing an immersive listening experience.

The Infinity L30 is a floor-standing speaker that emphasizes powerful sound and a stylish form factor. One of its key features is the incorporation of Infinity’s proprietary EMIT (Electromagnetic Induction Tweeter) technology. This technology is known for delivering exceptionally clear high frequencies, allowing listeners to experience the finer details in their music. The L30 also features a robust bass reflex design, which enhances low-frequency response, resulting in a richer sound experience. The speaker's design typically includes a high-quality, wooden cabinet that helps to minimize unwanted vibrations while adding an aesthetic appeal to any room.

On the other hand, the Infinity M30 is a bookshelf speaker designed for more compact environments without compromising sound quality. It shares several technologies with the L30, including the EMIT tweeter, ensuring that high-frequency reproduction remains clear and detailed. The M30's design also includes a rear-firing bass port, which helps to improve the bass response, making it suitable for a variety of setups, whether they are part of a home theater system or a dedicated stereo setup. The speaker is designed for versatility, easily fitting into various decor styles while delivering impressive sound quality.

Both speakers benefit from Infinity’s meticulous engineering, ensuring that they provide an exceptional audio experience. Features such as high-efficiency drivers, a wide frequency range, and the inclusion of durable materials contribute to their performance and longevity. Users can expect these speakers to produce sound with great accuracy and depth, making them ideal for genres ranging from classical to modern pop.

In summary, the Infinity L30 and M30 are exemplary models that showcase Infinity’s dedication to producing high-performance audio solutions. With advanced technologies, such as the EMIT tweeters, and thought-out designs aimed at maximizing sound quality, both models make powerful additions to any audio setup, promising to elevate the listening experience for users. Whether for music or movies, the L30 and M30 are sure to impress with their sonic capabilities and visual appeal.
Top Page Image Contents