Kenmore KWX - 6V, KWX - 9V, KWX - 8V KWX-3V KWX-4V, KWX-5V, KWX-6V, KWX-7V, KWX-8V, KWX-9V

FIG.

1

-ASME R[[J_¥

VALVE

DAMPER

--A

u

TEMP./PRESS.

GAUGE

C_

VI£NT

l

hr_

l

I I

II

r---

,-_

-I,

ENCLOSED

[_-----

SCOHTROL_

I

I

J I

r' 'E'r'PPLE

i<\/

I

I

J

i

I

I

?

I;[ HPT

,

\

\

I

I

i

31?

®

"_

i

\.A

• _AJN VALVE %

_._L_ _.1__ _1__ _

GAS VALVE

COH_OL

!

i L

,.Lr'--_l_

[

LEFT S;DE

RIGHT SIO[

BASIC BOILER		MODEL	NO.		NATURAL GAS		DIMENSIONS	(INCHES)
ConUnuous		Pilot	NO. OF	AGA/CGA	HEATING	NET	FLUE	"A"
	With		SECTIONS	INPUT	CAPACITY	I=B=R
							DIAMETER	WIDTH
Vent	Damper			*MBH	*MBH	Ratin9*MBH
KWX-3V			3	70	57	5O	5	11	1/4
KWX-4V			4	105	85	74	6	14	1/2
KWX-5V			5	140	113	98	6	17	¾
KWX-6V			6	175	142	123	7	21
KWX-7V			7	210	170	148	7	24	1/4
KWX-8V			8	245	198	172	7	27	1/2
KWX-9V			9	280	226	197	7	30	¾
* MBH = 1,000 Btuh	Btuh = British Thermal Unit Per Hour

For altitudes above 2,000 ft. ratings should be reduced at the rate of 4a_ for each 1,000 ft. above sea level• Heating Capacity is based on D.O.E (Deparirnent of Energy) test procedure.

**Add 5 ½" to height for Vent Damper.

The Ratings marked "Net I=B-R Ratings" indicate the amount of remaining heat input that can be used to heat the radiation or terminal Units. The net I=B=R Ratings shown are based on an allowance of 1.15 in accordance with the factors shown on the I=B=R Standard

as published by the Hydronies Institute. Selection of boiler size should be based upon "Net I=B=R Rating" being equal to or greater

than the calculated heat loss of the building. The Manufacturer should be consulted before selecting a boiler for installations having

unusual piping and pickup requirements. These boilers must stand on a non-combustible floor. If installed on a combustible floor, use

Combustible Floor Base Number 42135-1 or 146-14-031 (3-6 section boilers) or 42135-2 or 146-14-032 (7-9 section boilers).

BOILERS FOR USE AT HIGH ALTITUDE

This boiler is factory equipped for use at altitudes of 0-2,000feet above sea level. For use at altitudes above sea level, the input ratings are reduced by a change in main orifice size.

For altitudes above 2,000 feet above sea level, input ratings should be reduced at the rate of 4% for each 1,000 feet

above sea level. Consult the National Fuel Gas Code (NFPA54/ANSI Z223.1-1atest edition), or the manufacturer for correct orifice

sizing information. High altitude orifices are available from the boiler manufacturer.