Burnham V9A manual Shipping Information

Page 29

 

Number

 

 

 

Approx.

Approx.

Boiler

Length

Width

Height

Center of

Shipping

Model

of

A

B*

C**

Gravity

Weight

Sections

 

 

 

 

 

D***

LBS***

V903A

3

63-5/8

34-1/2

61

17-1/2

1478

V904A

4

69-5/8

34-1/2

61

20-1/2

1790

V905A

5

75-5/8

34-1/2

61

23-1/2

2102

V906A

6

81-5/8

34-1/2

61

27-1/2

2418

V907A

7

87-5/8

34-1/2

61

30-1/2

2734

V908A

8

93-5/8

34-1/2

61

33-1/2

3071

V909A

9

105-5/8

34-1/2

61

37-1/2

3452

V910A

10

111-5/8

34-1/2

61

40-1/2

3809

V911A

11

117-5/8

34-1/2

61

43-1/2

4120

V912A

12

123-5/8

34-1/2

61

46-1/2

4447

*Width can vary with gas train configuration.

If the V9A packaged boiler must pass through a 36” doorway, please specify.

**Add 6-1/2” to dimension C when equipped with optional top outlet.

***Varies slightly with burner and gas train configuration and with or without RTC.

1.Do not tilt. Exercise caution when lifting to avoid damage.

2.This boiler can be lifted by fork truck. Do not truck from front.

3.When lifting from rear, forks must extend beyond center of gravity and second skid cross bar.

4.When lifting from side, forks must extend to opposite skid rail and straddle center of gravity.

5.Cable spreader is to prevent jacket damage. Spreader width should equal B (width of skid) + 12”. Adjust cable lengths to lift at approximate center of gravity per chart.

Figure 25: Shipping Information

L.BOILER PIPING - HEATING APPLICATIONS CONNECT SUPPLY AND RETURN PIPING TO HEATING SYSTEM

Connect supply and return piping to heating system (see Figures 26 through 32). Flow direction for hot water boilers must be from the rear return out through the top front supply. Steam boilers can pipe return to the front as an alternate location. Some boiler sizes may require the use of additional supply and return tappings. Check Figure 24 and applicable piping diagram for the boiler size you are installing.

WARNING

Failure to properly pipe boiler may result in improper, unsafe system operation and void manufacturer’s warranty.

DO NOT improperly pipe boiler.

WARNING

All steam and hot water pipes must have clearances of at least 1/2” from all combustible construction.

WARNING

A hot water boiler installed above radiation level must be provided with a low water cutoff device as part of the installation.

1.HOT WATER HEATING - This boiler must be installed in strict accordance with this installation manual Deviations from these installation instructions may void manufacturer’s warranty. Also consult I=B=R Installation and Piping Guides.

WARNING

Continued boiler operation for prolonged periods of time under conditions when temperature differential across the system exceeds 40°F and/ or, return water temperature stays below 135°F, may result in premature boiler failure due to flue gas condensation and/or thermal shock.

a.If the boiler is used in connection with refrigeration systems, boiler must be installed with chilled medium piped in parallel with heating boiler using appropriate valves to prevent chilled medium from entering boiler. See Figure 35.

b.If the boiler is connected to heating coils located in air handling units where they may be exposed to refrigerated air, boiler piping must be equipped with flow control valves to prevent gravity circulation of boiler water during cooling system operation.

c.Burnham Commercial recommends maintaining temperature differential (drop) across the system at 40°F or less, and return water temperature at minimum of 135°F for optimum operation and long-term reliability.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents V9A Series Boiler Page USA Boilers Important Information Read CarefullyPage Page Table of Contents Table of Contents Section I General Information Table I Boiler Ratings / Data Locate the Unit Recommended Service ClearanceChimney or Vent Typical Arrangement for Stub Vent Right Assembly of Sections Manual DRAW- UP Section II Cast Iron Block AssemblySetting of Nipples V9A Section Arrangement Assembly of Sections Hydraulic DRAW-UP Front and Rear Section Channel Hydraulic Draw-Up Sections Section III Installation Instructions Bare Boiler Assembly Avoid Breathing Fiber Particulates and Dust Left Side Canopy Intermediate Bracket Inspect ALL Boiler Seals Mount Rear Observation Port Cover Refer to FigureV9A Series Jacket Assembly Boiler Models V903A thru V912A Mount Burner Adapter Plate to Burner Mounting Plate Burner Mounting Plate Refer to Figures 16Water Boilers Install Water Trim Steam Boilers Install Steam TrimPackaged Boiler Burner InstallationShipping Information Page V9A Series Minimum Piping Parallel Water Boiler V9A Series Minimum Piping Primary Secondary Water Boiler Page Page Page Page Page Page Page Mounting Elevations of M&M 150 Float Low Water Cut-Offs Schematic Tankless Heater Piping Page DHW Generation with Indirect Water Heater Water Boiler Pressure Relief Valve Hook-Up Section IV Operating Instructions Always Inspect Installation Before Starting BurnerTest Controls Boiler and System Cleaning Steam BoilerBoiler and System Cleaning Water Boilers Oxygen Corrosion Frequent Water AdditionClean the Boiler Flueways Section V Service InstructionsProbe Type LOW Water Cutoff Maintenance of LOW Water Cutoff DevicesGeneral Maintenance Considerations OIL Burners Section VI Burner SpecificationsCombination GAS / OIL Burners Table VII Webster Burner Specifications Head Band Low High Fire Section VII Repair PartsSection VII Repair Parts Jacket Repair Parts Models V903A Thru V912A Bare Boiler Assembly Repair Parts for Bare Boiler Assembly Repair Parts for Bare Boiler Assembly Steam Trim / Water Trim Service Record Service Record

V9A specifications

Burnham V9A is a well-established model in the world of cast iron boilers, renowned for its efficiency and reliability in residential heating applications. As a part of Burnham's esteemed line of heating solutions, the V9A is designed to provide homeowners with consistent warmth while prioritizing fuel economy and ease of use.

One of the defining features of the Burnham V9A is its durable cast iron construction. This robust material enables the boiler to withstand high temperatures and pressures, ensuring a long service life. The V9A is engineered with several sections that are joined together, allowing for easier maintenance and potential adaptability to various heating demands. The boiler's design also promotes excellent heat retention, which not only enhances performance but contributes to overall energy efficiency.

In terms of technology, the Burnham V9A stands out with its advanced combustion design. With an efficiency rating of up to 85%, this model maximizes the heat output while minimizing fuel consumption. The boiler is compatible with both natural gas and propane, providing flexibility for users to choose their preferred fuel source. Additionally, the V9A is designed to operate with a minimum of venting requirements, making installation simpler and more cost-effective.

The Burnham V9A also features a choice of various firing rates, allowing homeowners to select the optimal heating output for their specific needs. This versatility ensures that the boiler can be effectively sized for different home environments, making it a highly adaptable option for a broad range of residential settings.

Moreover, one key characteristic of the Burnham V9A is its user-friendly control systems. It comes equipped with reliable electronic ignition and offers options for outdoor reset controls, which enhance efficiency by adjusting the boiler's operation based on the outdoor temperature. This advanced control capability not only optimizes energy use but also enhances comfort levels in the home.

Overall, the Burnham V9A represents a balance of durability, efficiency, and modern convenience, making it a top choice for homeowners seeking a reliable heating solution. Its combination of cast iron construction, advanced technology, and user-friendly features solidify its reputation in the competitive market of heating systems, ensuring comfort and peace of mind for years to come.
Top Page Image Contents