Heat & Glo LifeStyle 8000TV-OAK-IPI, 8000TVLP-OAKIPI Log Assembly LOGS-8OAK, Positioning the Logs

Page 27

F. Positioning the Logs

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

CAUTION: Carefully remove the logs from the packaging. Logs are fragile!

Log Assembly: LOGS-8OAK

LOG TABS

B A A B

B AB

STEP 1: Remove metal grate supports (A) and refractory tabs (B) by using a back and forth motion until the tabs break free. Metal tabs and supports are needed for shipping only. After removing the tabs and supports, the grate should fully rest on the base refractory.

LOG TAB

1

2

1

STEP 2: Log #1 (SRV2057-720): Place log 1 so that the bottom right notch on log rests on far right grate tine. The bottom left notch on log #1 must mate over the log tab on the burner face.

STEP 3: (SRV2057-721): Place log 2, nose to nose with log 1. The bottom notch on log #2 must mate over the log tab on the burner face.

AB

21

3

21

STEP 4: (SRV2057-722): Place log 3 so that the bottom notches mate with the 2 back steel tabs. Tab A is located on the

right side of pilot bracket, tab B is located at the back/right corner of burner. NOTE: There should be a 1/2 inch gap between the bottom of log 3 and the top edge of the burner. The underside of log #3 must not cover ANY burner ports.

Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08

2057-935C

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Models 8000TV-OAK 8000TV-OAK-IPI 8000TVLP-OAKIPI Homeowner Reference Information CongratulationsTable of Contents Glass Specifications High Altitude InstallationsListing and Code Approvals Appliance CertificationCode CSA C22.1 Non-Combustible Materials SpecificationCombustible Materials Specification Electrical CodesGetting Started Design and Installation ConsiderationsNegative Pressure Inspect Appliance and Components Tools and Supplies NeededSelecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseClearances to mantels or other combustibles above appliance Mantel ProjectionsVent Termination Minimum Clearances Termination LocationsModels Pipe Size Vent Information and DiagramsVent Guidelines Vent System ConfigurationMaximum Horizontal Feet Minimum Vertical 9 Feet Vent Clearances and Framing Pipe Clearances to CombustiblesVertical Penetration Framing Securing and Leveling Appliance Installing Outside Air Kit Damper AssemblyAppliance Preparation Gas and Electrical ConnectionsChecking Pilot Plate Completing Grate Set-upAttaching Vent to Firebox Installing Vent PipeAssembly of Vent Sections Securing Vent SectionsGas Information Fuel Conversions Gas ConnectionGas Pressures High Altitude Installations Electrical Information Recommendation for WireConnecting to the Appliance Wall SwitchOptional Accessories Requirements Intellifire Ignition System WiringIntellifire Pilot Ignition IPI Wiring Diagram Standing Pilot Ignition System WiringWall Switch Installation for Fan Optional Junction Box InstallationFacing Material FinishingAppliance Setup Positioning the Logs Log Assembly LOGS-8OAKPage Grilles and Trim Glass AssemblyShutter Settings Screen MeshBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance Check Appliance DraftFinal inspection by Lighting Appliance IPI IgnitionStanding Pilot Ignition For Your Safety Read Before Lighting InstructionsFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingSympton Possible Cause Corrective Action Intellifire Ignition Systemflame has been lit, flame Maintaining and Servicing Appliance Maintenance TasksDoors, Surrounds Inspect Maintenance TasksReference Materials Appliance Dimension DiagramLog Set Assembly Service PartsPart number list on following Service Parts List StockedAt Depot 8000TV-OAK-IPI IPI Valve Assembly8000TV-OAK Standing Pilot Valve AssemblyLimited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime WarrantyDo not Discard this Manual Contact Information

8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI specifications

The Heat & Glo LifeStyle 8000TVLP-OAKIPI, 8000TV-OAK-IPI, and 8000TV-OAK are cutting-edge fireplace units that redefine the way we experience warmth and ambiance in our homes. Designed with a sleek and modern aesthetic, these gas fireplaces offer an ideal blend of style, comfort, and efficiency.

One of the standout features of the LifeStyle 8000 series is its expansive viewing area, which allows homeowners to enjoy an unobstructed view of the flickering flames. The large glass display not only enhances the visual appeal but also creates a welcoming atmosphere in any living space. The unit's clean lines and contemporary design ensure it complements a wide range of interior styles, from traditional to modern.

Efficiency is a hallmark of the LifeStyle 8000 series. Equipped with advanced heating technologies, these fireplaces provide effective warmth while utilizing fuel efficiently. The patented IntelliFire technology allows for easy ignition and reliable performance. Users can enjoy the convenience of controlled heat settings, ensuring that their space remains comfortable without excessive energy use.

Moreover, the LifeStyle series incorporates innovative safety features that provide peace of mind. With automatic shut-off options, homeowners can relax knowing that the fireplace will operate safely and efficiently. The removable mesh screen adds an extra layer of security while allowing families to enjoy the ambiance without worry.

Customization is another key aspect of the Heat & Glo LifeStyle 8000 series. Homeowners can choose from a variety of finishes, making it easy to match their fireplace to their home’s decor. Options for decorative media, such as glass and logs, allow users to create a look that suits their personal style.

Installation is made simple with the flexible venting options provided by these units. The designers have prioritized user-friendliness by ensuring that the units can fit into a variety of spaces, making them an excellent choice for both new builds and renovations.

In summary, the Heat & Glo LifeStyle 8000TVLP-OAKIPI, 8000TV-OAK-IPI, and 8000TV-OAK are impressive gas fireplaces that combine efficiency, safety, and aesthetic appeal. With their high-quality construction, advanced technology, and customizable features, they offer a luxurious and practical solution for any home seeking warmth and ambiance.
Top Page Image Contents