Heat & Glo LifeStyle 8000TV-OAK-IPI, 8000TVLP-OAKIPI owner manual Intellifire Ignition System

Page 36

B. Intellifire Ignition System

Sympton

Possible Cause

Corrective Action

 

 

 

1. The ignitor/module

a. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor

makes noise, but no

 

are connected to correct terminals on module and pilot assembly.

spark.

 

Reversed wires at the module may cause system to make sparking

 

 

noise, but spark may not be present at pilot hood.

 

 

 

 

b. Loose connections or electrical

Verify no loose connections or electrical shorts in wiring from mod-

 

shorts in the wiring.

ule to pilot assembly. Rod closest to pilot hood should be ignitor.

 

 

Verify connections underneath pilot assembly are tight; also verify

 

 

connections are not grounding out to metal chassis, pilot burner,

 

 

pilot enclosure, mesh screen if present, or any other metal object.

 

 

 

 

c. Ignitor gap is too large.

Verify gap of igniter to pilot hood. The gap should be approximately

 

 

.17 inch or 1/8 inch.

 

 

 

 

d. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place ON/OFF Rocker switch or wall

 

 

switch in ON position. Hold ground wire about 3/16 inch away from

 

 

“I” terminal on module. If there is no spark at “I” terminal module

 

 

must be replaced. If there is a spark at “I” terminal, module is fine.

 

 

Inspect pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode.

 

 

 

2. Pilot won’t light,

a. Transformer installed correctly.

Verify that transformer is installed and plugged into module. Check

there is no noise or

 

voltage of transformer under load at spade connection on module

spark.

 

with ON/OFF switch in ON position. Acceptable readings of a good

 

 

transformer are between 3.2 and 2.8 volts AC.

 

 

 

 

b. A shorted or loose connection in wir-

Remove and reinstall the wiring harness that plugs into module.

 

ing configuration or wiring harness.

Verify there is a tight fit. Verify pilot assembly wiring to module.

 

 

Remove and verify continuity of each wire in wiring harness.

 

 

 

 

c. Improper wall switch wiring.

Verify that 110/VAC power is “ON” to junction box.

 

 

 

 

d. Module not grounded.

Verify black ground wire from module wire harness is grounded to

 

 

metal chassis of appliance.

 

 

 

 

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place ON/OFF Rocker switch or wall

 

 

switch in ON position. Hold ground wire about 3/16 inch away from

 

 

“I” terminal on module. If there is no spark at “I” terminal module

 

 

must be replaced. If there is a spark at “I” terminal, module is fine.

 

 

Inspect pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode.

 

 

 

3. Pilot lights but con-

a. A shorted or loose connection in

Verify all connections to wiring diagram in manual. Verify connec-

tinues to spark, and

sensor rod.

tions underneath pilot assembly are tight. Verify connections are

main burner will not ig-

 

not grounding out to metal chassis, pilot burner, pilot enclosure or

nite. (If the pilot contin-

 

screen if present, or any other metal object.

ues to spark after the

 

 

b. Poor flame rectification or contami-

Verify that flame is engulfing sensor rod. If the pilot assembly does

pilot flame has been lit,

flame rectification has

nated sensor rod.

not have a ground strap, consider installing one to increase flame

 

rectification. Verify correct pilot orifice is installed and inlet gas

not occurred.)

 

 

specifications. Flame carries rectification current, not the gas. If

 

 

 

 

flame lifts from pilot hood, the circuit is broken. A wrong orifice or

 

 

too high an inlet pressure can cause pilot flame to lift. The sensor

 

 

rod may be contaminated. Clean sensor rod with emery cloth.

 

 

 

36

Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Models 8000TV-OAK 8000TV-OAK-IPI 8000TVLP-OAKIPI Congratulations Homeowner Reference InformationTable of Contents High Altitude Installations Listing and Code ApprovalsAppliance Certification Glass SpecificationsNon-Combustible Materials Specification Combustible Materials SpecificationElectrical Codes Code CSA C22.1Design and Installation Considerations Getting StartedNegative Pressure Tools and Supplies Needed Inspect Appliance and ComponentsFraming and Clearances Selecting Appliance LocationConstructing the Appliance Chase ClearancesMantel Projections Clearances to mantels or other combustibles above applianceTermination Locations Vent Termination Minimum ClearancesVent Information and Diagrams Vent GuidelinesVent System Configuration Models Pipe SizeMaximum Horizontal Feet Minimum Vertical 9 Feet Vent Clearances and Framing Pipe Clearances to CombustiblesVertical Penetration Framing Installing Outside Air Kit Damper Assembly Appliance PreparationGas and Electrical Connections Securing and Leveling ApplianceCompleting Grate Set-up Checking Pilot PlateInstalling Vent Pipe Assembly of Vent SectionsSecuring Vent Sections Attaching Vent to FireboxGas Information Fuel Conversions Gas ConnectionGas Pressures High Altitude Installations Recommendation for Wire Connecting to the ApplianceWall Switch Electrical InformationIntellifire Ignition System Wiring Optional Accessories RequirementsStanding Pilot Ignition System Wiring Intellifire Pilot Ignition IPI Wiring DiagramJunction Box Installation Wall Switch Installation for Fan OptionalFinishing Facing MaterialAppliance Setup Log Assembly LOGS-8OAK Positioning the LogsPage Glass Assembly Shutter SettingsScreen Mesh Grilles and TrimOperating Instructions Before Lighting ApplianceCheck Appliance Draft Before operating this appliance have a qualified technicianLighting Appliance IPI Ignition Final inspection byFor Your Safety Read Before Lighting Instructions Standing Pilot IgnitionFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionIntellifire Ignition System Sympton Possible Cause Corrective Actionflame has been lit, flame Maintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsLog Set Assembly Service PartsPart number list on following Service Parts List StockedAt Depot IPI Valve Assembly 8000TV-OAK-IPIStanding Pilot Valve Assembly 8000TV-OAKLimited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information Do not Discard this Manual

8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI specifications

The Heat & Glo LifeStyle 8000TVLP-OAKIPI, 8000TV-OAK-IPI, and 8000TV-OAK are cutting-edge fireplace units that redefine the way we experience warmth and ambiance in our homes. Designed with a sleek and modern aesthetic, these gas fireplaces offer an ideal blend of style, comfort, and efficiency.

One of the standout features of the LifeStyle 8000 series is its expansive viewing area, which allows homeowners to enjoy an unobstructed view of the flickering flames. The large glass display not only enhances the visual appeal but also creates a welcoming atmosphere in any living space. The unit's clean lines and contemporary design ensure it complements a wide range of interior styles, from traditional to modern.

Efficiency is a hallmark of the LifeStyle 8000 series. Equipped with advanced heating technologies, these fireplaces provide effective warmth while utilizing fuel efficiently. The patented IntelliFire technology allows for easy ignition and reliable performance. Users can enjoy the convenience of controlled heat settings, ensuring that their space remains comfortable without excessive energy use.

Moreover, the LifeStyle series incorporates innovative safety features that provide peace of mind. With automatic shut-off options, homeowners can relax knowing that the fireplace will operate safely and efficiently. The removable mesh screen adds an extra layer of security while allowing families to enjoy the ambiance without worry.

Customization is another key aspect of the Heat & Glo LifeStyle 8000 series. Homeowners can choose from a variety of finishes, making it easy to match their fireplace to their home’s decor. Options for decorative media, such as glass and logs, allow users to create a look that suits their personal style.

Installation is made simple with the flexible venting options provided by these units. The designers have prioritized user-friendliness by ensuring that the units can fit into a variety of spaces, making them an excellent choice for both new builds and renovations.

In summary, the Heat & Glo LifeStyle 8000TVLP-OAKIPI, 8000TV-OAK-IPI, and 8000TV-OAK are impressive gas fireplaces that combine efficiency, safety, and aesthetic appeal. With their high-quality construction, advanced technology, and customizable features, they offer a luxurious and practical solution for any home seeking warmth and ambiance.
Top Page Image Contents