EMI manual CAC Cassette Evaporator Fascia Installation Instructions, Assembly Instructions

Page 11

CAC CASSETTE EVAPORATOR FASCIA INSTALLATION INSTRUCTIONS

Assembly Instructions

1. To install the four fascia mounting bolts:

a)Remove the bolts and wash- ers from the supplied kit bag.

b)Put washers onto the bolts.

c)Screw the mounting bolt with washer into the chassis leav- ing approximately 1” to hang the fascia.

4.On 18-36k units connect the vane motor plug by plugging it into the socket con- nection on the chassis.

a)Ensure that the connector is in the proper orientation.

Female vane motor plug on chassis

Male vane motor plug on fascia

2.Ensure the white fi r tree fasteners holding the fascia polystyrene are pushed fi rmly in

(they may have sened in nsit).

3.Lift the fascia onto the chassis mount- ing bolts. Align the key hole brackets with the mounting bolts and slide the fascia forward to lock into position.

Note: The fascia only fi ts correctly one way. Position the fascia so that the AmericaSeries logo is on the control box end of the chassis.

b)Route the wires in a way that en- sures they won’t become trapped, cut, broken or chaffed.

5.The fascia can now be tight-

ened up to the Cassette chassis. Make sure a good seal is obtained between fascia and chassis, this is neces- sary to prevent recir- culation.

Note: Do not over tight- en the bolts. To do so may cause damage to the fascia.

With fi lter(s) in place, the inlet grille(s) can now be installed onto the fascia.

To complete the installation adjust the lou- ver position to 30° from plumb, this is recom- mended for

“optimum” system per- formance.

CAC Cassette Evaporator

11

www.enviromaster.com

Image 11
Contents Nominal Circuit Capacities INSTALLATION, Operation and Maintenance ManualCAC Cassette High Efficiency Evaporator To the InstallerSafety Instructions System Options Standard FeaturesProduct Description CAC Cassette Controls and Components Preparation for InstallationLarge Unit Small Unit ShownMedium Unit Shown CAC Cassette Preparation and Positioning PISTON/ORIFICE Installation InstructionCeiling opening Mounting the CAC Cassette Ceiling EvaporatorMAX CAC Cassette Chassis Positioning and InstallationCondensate Piping Correct IncorrectUse of a larger line can harm Compressor Piping DO’S and DON’TS Pipe Installation NotesRefrigeration Piping Assembly Instructions CAC Cassette Evaporator Fascia Installation InstructionsMake sure power is off CAC Cassette Evaporator Installation InstructionsElectrical Wiring Low Volt Interconnect Wiring High Volt Electrical WiringStart -UP for Wall Thermostat Control LOW Voltage Interconnect WiringFigure #4 Refrigerant Processing Important Notes CAC Cassette Evaporator Test Unit Performance Data Test Unit Performance Data SheetMaintenance and Troubleshooting Procedure Power Supply Check Troubleshooting ProcedureElectric Heat Low Volt ControlsCooling Only Units How long will the fan run? Frequently Asked QuestionsCAC Performance Data Discharge AIR VolumeSmall Cabinet CAC 9,000 12,000 CAC Cassette DimensionsMedium Cabinet CAC 18,000 24,000 Large Cabinet CAC 30,000 36,000 CAC Cassette System Matches CAC Electrical SpecificationsT2C, T3C & T4C Top Discharge Enviromaster International LLC ALL Product Limited WarrantyT2C, T3C & T4C 2, 3 & 4 Zone Top Discharge EMI’S High Efficiency Product LineHigh Wall Evaporator S1C & S1H Single Zone S2C Dual Zone

CAC specifications

EMI CAC, or Electromagnetic Interference Common-mode Current, is a critical concern in electronic device design and operation. It refers to the unwanted electromagnetic energy that can disrupt the normal functioning of electronic circuits, particularly in complex systems. EMI can arise from various sources, including power lines, radio frequency transmitters, and even other components within the same device.

One of the main features of EMI CAC is its dual nature. It can be both a source of interference and a metric to assess the integrity of electronic systems. The impacts of EMI are far-reaching, affecting communication signals, power supply reliability, and overall device performance. As technology progresses and devices become more compact, the likelihood of EMI issues increases, making it essential for engineers to develop effective solutions.

Several technologies are employed to mitigate EMI CAC in electronic systems. Shielding is one of the most common methods, involving the use of conductive materials to block electromagnetic fields. This can take the form of metal enclosures or coatings that prevent the escape of emissions. Another strategy involves the use of filters, such as ferrite beads and capacitors, which can suppress common-mode currents before they enter the sensitive parts of a circuit.

The characteristics of EMI CAC vary depending on several factors, including frequency, amplitude, and the specific environment in which the electronic devices operate. High-frequency EMI is particularly challenging due to its ability to penetrate enclosures and disrupt signals. Additionally, common-mode noise can often appear in differential signals, exacerbating the situation and making detection more difficult.

Achieving EMC (Electromagnetic Compatibility) is a major goal for designers dealing with EMI CAC. This involves not only reducing emissions from devices but also improving their immunity to external sources of interference. Effective grounding techniques and careful layout planning are crucial in minimizing EMI effects.

In summary, EMI CAC represents a significant challenge in modern electronics, with a need for advanced solutions to ensure device performance and reliability. By understanding its features, employing effective technologies for mitigation, and addressing its characteristics, engineers can create robust designs that thrive in the increasingly complex electromagnetic landscape of today’s technological world.