Carrier HUMCCLFP1025-A specifications → ÐInstall Drain Line

Remember to provide clearance for maintenance and evaporator pad removal. To access pad remove top or bottom cover to expose assembly (turn knob counter-clockwise).

Step 3ÐPrepare Plenum Opening (See Fig. 2.)

1.Use template for marking humidifier opening.

2.Tape in place on plenum making sure template is level.

IMPORTANT: For humidifier to operate properly it must be level and mounted on a vertical surface.

3.Drill four 1/8-in. holes in plenum.

4.Cut opening in plenum using heavy solid lines on template as a guide.

Step 4ÐMount the Humidifier (See Fig. 3.)

1.Attach foam tape on inside of mounting flange.

2.Hook bottom notch of humidifier on opening cut in plenum.

3.Push top of humidifier to plenum aligning screw holes with flange.

4.Align, level, and secure using top screws first.

5.Insert bottom screws and tighten all screws for air tight seal.

→Step 5ÐInstall Drain Line

1.Use 1/2- or 5/8-in. vinyl tubing (field supplied) to connect drain on bottom of humidifier housing to an open drain.

2.Use supplied worm drain clamp to hold drain tubing in position over drain fitting outlet.

Unit may leak if drain tubing is misapplied. Do not insert tubing inside of drain fitting outlet.

3.Make sure line is free of traps due to sagging and has sufficient pitch to drain.

Step 6ÐMake Water Connection

If garden hose is not used for water supply:

1.Mount saddle valve on water line according to instructions supplied with saddle valve.

2.Run 1/4-in. diameter (water line grade) tubing from saddle valve to adapter on solenoid valve and tighten compression fittings.

IMPORTANT: If water pressure is higher than normal (60 psi), use noise suppression disk included in parts bag. (Read water noise reducer note located inside package for instructions). For normal operation, saddle valve need only be opened 1 full turn to meet performance requirements.

3. Open valve and check installation for leaks.

NOTE: Saddle valve is self piercing on copper lines; 1/4-in. hole must be drilled in steel or iron pipes. Use only a grounded drill or a hand drill to avoid shock hazard. Turn off water and drain the pipe prior to drilling 1/4-in. hole.

Step 7ÐInstall Humidistat and Complete Wiring

1.Mount humidistat on inside wall, or return-air duct in accor- dance with section INSTALLATION OF HUMIDISTAT on page 10.

2.Wire red and blue low voltage. (See Fig. 6.)

3.Plug power cord in to 115-vac 60Hz source.

NOTE: Wiring must comply with National Electrical Code and any local codes or ordinances that may apply.

Step 8ÐStart-Up

1.Open saddle valve to permit water flow to the solenoid.

2.Check all connections for water leaks.

HUMIDIFIER	HUMIDISTAT
RED	24VAC
BLU	FURNACE

115V FIELD WIRING FAN TYPE UNITS ONLY

		TRANSFORMER
HUMIDIFIER	HUMIDISTAT	(FIELD SUPPLIED)
	RED		115V
	BLU	24V	FIELD
			WIRING

115V FIELD WIRING FAN TYPE UNITS ONLY

A96010

Fig. 6ÐInstallation of Humidistat

on Fan-Type Humidifier

3.Set thermostat to call for heat. Set humidistat for highest humidity setting making sure contacts are closed. After a few minutes of operation, check the drain connection for leaks and to see if water is flowing through humidifier.

4.Reverse thermostat and humidistat settings to insure proper shutdown.

5.Reset thermostat to normal setting. Reset humidistat to rec- ommended setting.

Step 9ÐFinal Steps

Attach humidifier maintenance instruction sticker to a visible location.

1.Inform homeowner of proper operation, maintenance, and humidistat setting.

a.If unit is installed during cooling season set humidistat for summer setting (OFF or lowest setting).

b.If installed during heating season, set unit for normal operation.

INSTALLATION OF HUMCCSFP1016-A--

FAN POWERED HUMIDIFIER

Carrier's HUMCCSFP1016-A-- fan powered humidifier can only be installed on the supply plenum of a forced-air system. This unit requires an external 115-vac (fused) plug-in receptacle near the equipment for proper operation.

It is recommended to install the humidifier where it can be easily serviced. Pad access door can be easily converted from right to the left hand side. Always install humidifier downstream of an electronic air cleaner.

→Step 1ÐInspect Package and Check Equipment

Inspect contents of packaged humidifier. File claim with shipping company prior to installation, if shipment is damaged or incom- plete.

The package should contain:

1.Humidifier and media assembly

2.Humidistat

3.Template

4.Owner's Manual

5.Warranty Certificate

6.Solenoid valve

4