Carrier HUMCCLFP1025-A ÐMount Solenoid Valve, Installation of HUMCCSBP2017-A Bypass Humidifier

Page 6

SOLENOID

VALVE

INLET HOLE

HOUSING

SEAT

ENCLOSURE

SOLENOID

 

VALVE

 

FLUSH

 

AGAINST

 

INLET

 

A97107

Fig. 10ÐTop Mounting of Water Solenoid Valve

Step 6ÐMount Solenoid Valve

The water solenoid valve should be mounted on top of humidifier enclosure.

1.To mount solenoid on top, see Fig. 10.

a.Firmly press valve into the top inlet hole on enclosure. Seat valve flush against inlet hole.

2.If alternate mounting of solenoid is required, see Fig. 11.

a.To mount solenoid on side, use 3/8-in. ID, 1/2-in. OD vinyl tubing (field supplied). Place tubing onto valve stem and secure with clamp.

b.Mount valve upside down securing to side of housing.

c.Place open end of tubing into the top inlet hole.

IMPORTANT: Be careful not to kink tubing.

Step 7ÐMake Water Connection

If garden hose is not used for water supply:

1.Mount saddle valve on water line according to instructions supplied with valve.

2.Run 1/4-in. diameter (water line grade) tubing from saddle valve to adapter on solenoid valve and tighten compression fittings.

IMPORTANT: If water pressure is higher than normal (60 psi), use noise suppression disk included in parts bag. (Read water noise reducer note located inside package for instructions). For normal operation, saddle valve need only be opened 1 full turn to meet performance requirements.

3. Open valve and check installation for leaks.

NOTE: Saddle valve is self piercing on copper lines; 1/4-in. hole must be drilled in steel or iron pipes. Use only a grounded drill or a hand drill to avoid shock hazard. Turn off water and drain the pipe prior to drilling 1/4-in. hole.

Step 8ÐInstall Humidistat and Complete Wiring

1.Mount humidistat on inside wall, or return-air duct in accor- dance with section INSTALLATION OF HUMIDISTAT on page 10.

2.Wire red and blue low-voltage leads. (See Fig. 6.)

3.Plug power cord in to 115-vac 60Hz source.

NOTE: Wiring must comply with National Electrical Code and any local codes or ordinances that may apply.

TUBING

ENCLOSURE

INLET HOLE

POSITION TUBING INSIDE INLET HOLE (CUT LENGTH

IF REQUIRED)

A97099

Fig. 11ÐAlternate Mounting of Solenoid Valve

on HUMCCSFP1016-A-- Humidifier

Step 9ÐStart-Up

1.Open saddle valve to permit water flow to the solenoid.

2.Check all connections for water leaks.

3.Set thermostat to call for heat. Set humidistat for highest humidity setting making sure contacts are closed. After a few minutes of operation, check the drain connection for leaks and to see if water is flowing through humidifier.

4.Reverse thermostat and humidistat settings to insure proper shutdown.

5.Reset thermostat to normal setting. Reset humidistat to rec- ommended setting.

Step 10ÐFinal Steps

Attach humidifier maintenance instruction sticker to a visible location.

1.Inform homeowner of proper operation, maintenance, and humidistat setting.

a.If unit is installed during cooling season set humidistat for summer setting (OFF or lowest setting).

b.If installed during heating season, set unit for normal operation.

INSTALLATION OF HUMCCSBP2017-A--

BYPASS HUMIDIFIER

Carrier's HUMCCSBP2017-A-- bypass humidifier can be in- stalled on either the supply or return plenum of a forced air system. This unit requires an external bypass duct between the supply- and return-air ductwork.

It is recommended to install the humidifier where it can be easily serviced. If this humidifier is installed with a central cooling system the bypass duct must have a shutoff damper to close during the cooling season. Always install humidifier downstream of an electronic air cleaner.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Safety Considerations Installation of HUMCCLBP2018-A Bypass Humidifier→ Humidifiers → ÐInstallation of HUMCCLBP2018-A-- Bypass-Type Humidifier → ÐMounting the Humidifier→ ÐInstallation of Humidistat on Bypass-Type Humidifier → ÐInstallation of HUMCCLFP1025-A-- Fan-Type HumidifierInstallation of HUMCCLFP1025-A FAN Powered Humidifier → ÐInstall Drain Line Installation of HUMCCSFP1016-A FAN Powered HumidifierSelect Location See Fig ÐMount the HumidifierInstallation of HUMCCSBP2017-A Bypass Humidifier ÐMount Solenoid Valve→ ÐInstallation of HUMCCSBP2017-A Bypass-Type Humidifier → ÐMounting Solenoid Valve on HUMCCSBP2017-A-- HumidifierÐMount Humidifier Installation of HUMCCWTR2019-A Bypass Water Saver Humidifier → ÐValve and Media Assembly for HUMCCWTR2019-A → ÐInstallation of HUMCCWTR2019-A-- Water Saver HumidifierInstallation of Humidistat ÐWall Mounting Low VoltageÐWiring ÐAdjustmentÐDuct Mounting Low Voltage Recommended Humidistat Setting ÐOperationÐCheckout

HUMCCLFP1025-A specifications

The Carrier HUMCCLFP1025-A is a high-performance air handling unit designed for modern commercial and industrial applications. This model stands out due to its advanced engineering, energy efficiency, and superior air quality management. It addresses the growing demand for effective climate control solutions while ensuring compliance with environmental regulations.

One of the primary features of the HUMCCLFP1025-A is its innovative design, which promotes optimal airflow and temperature regulation. The unit is equipped with a multi-speed fan system that allows for precise adjustments based on the requirements of the space. This flexibility ensures reduced energy consumption while maintaining comfort levels. Additionally, its advanced EC motor technology enhances operational efficiency, leading to significant energy savings over time.

The HUMCCLFP1025-A also incorporates a robust filtering system that captures airborne pollutants, allergens, and particulate matter. The unit utilizes high-efficiency filters, which improve the overall air quality while extending the life of the equipment. The integration of a demand-controlled ventilation system further maximizes efficiency by adjusting the airflow based on occupancy levels, ensuring that only the necessary amount of conditioned air is supplied.

Another noteworthy characteristic of this model is its modular construction. The HUMCCLFP1025-A can be easily customized to meet the specific requirements of various applications. This adaptability allows for easy installation and maintenance, making it a practical choice for building managers and HVAC contractors alike. The unit is designed for quiet operation, minimizing noise disruption in sensitive environments such as offices and healthcare facilities.

Furthermore, the Carrier HUMCCLFP1025-A features advanced connectivity options, including compatibility with Building Management Systems (BMS). This allows for remote monitoring and control, enabling operators to optimize performance and troubleshoot issues in real time. The integration of smart technologies enhances the unit's capabilities, making it a forward-thinking solution in HVAC systems.

In conclusion, the Carrier HUMCCLFP1025-A is a versatile and efficient air handling unit that combines sophisticated design, advanced technology, and superior air quality management. Its range of features, including energy efficiency, customizable configurations, and smart connectivity, make it an ideal choice for various commercial and industrial environments. As the demand for sustainable and effective climate control solutions continues to grow, the HUMCCLFP1025-A stands out as a reliable option that meets the needs of today and the future.
Top Page Image Contents