Honeywell IPGSM-DP manual PowerBoost1

Page 6

IPGSM-DP Commercial Fire Communicator – Installation and Setup Guide

3.Install the two plastic mounting rails for the LED Display board. They simply snap into the back plate holes.

4.Connect the LED Display board to its connector, then slide the board into the mounting rails. (Yellow LED and Buzzer are on top.)

5.Carefully remove the packaging material that surrounds the PowerBoost1.

6.Mount the PowerBoost1 on the three unused standoffs. Use the plastic screw (prevents shorting) to secure the upper right corner of the PowerBoost1 and the two metal screws and lock washers to fasten the left side of the circuit board. Ensure the lock washers are located between the circuit board and the head of the two metal screws.

7.Mount the Wall Outlet Box to an un-switched facility power outlet and run a conduit to the cabinet.

8.In this step DO NOT plug the transformer in. Route 16AWG wire from the transformer, through the conduit. Pass the wires through the Ferrite Filter, then loop the wires back through again making a loop. Connect the wires to the PowerBoost1 AC terminals.

9.Connect and route 16AWG insulated wire from facility power ground (typically a cold water pipe) to the cabinet's ground post. Ensure all ground connections are tight.

10.Connect the Ethernet cable and the Telco 1 and Telco 2 lines. If you choose to use an optional Cabinet Tamper Switch (if the control panel supports it) mount and wire it.

Note: The Ethernet cable, Telco 1, Telco 2 lines, and the optional cabinet Tamper Switch (if used) must be run through conduit.

11.Verify the PowerBoost1 module DIP switches are configured as shown below.

PowerBoost1

-V0

ON

 

 

 

 

 

 

 

 

 

008-COM-iPGSM

1

2

3

4

5

 

ON

1 2 3 4 5

(Switch handle = white)

12.Ensure the following:

LED Display board is fully seated.

All wiring terminals and connectors are tight.

All wiring has been completed and secured with cable ties.

13.Install the battery (not supplied). Plug the power transformer in, and attach the battery cable.

4

Image 6
Contents IPGSM-DP Contents Installation General InformationOperation Activate the SIM and Setup the Customer Account Register the Communications Module with AlarmNetDetermine the Signal Strength and Select a Location Mount and WirePowerBoost1 Transformer N8167 ConduitProgram the Communications Module 7720P ProgrammerConfigure the Fire Panel Test the SystemIPGSM-DP Trouble Detection Information Dialer Capture Module InformationLED Display Information PowerBoost1 Module Information ActiveIGSM Communications Module Information OFF Normal Slow Blink Loss of communication withIPGSM-DP Specifications RF SpecificationsPage Wiring Diagram + BatteryÊ800-08074AŠ

IPGSM-DP specifications

The Honeywell IPGSM-DP is an advanced communication device specifically designed for alarm signaling and monitoring in contemporary security systems. This state-of-the-art unit is engineered to enhance the efficiency and reliability of alarm communications, serving as an integral part of home and business security solutions.

One of the main features of the IPGSM-DP is its dual-path communication capability, allowing it to connect via both cellular networks and the internet. This dual communication method ensures that security signals are transmitted even in situations where traditional phone lines may fail or be compromised. This capability is particularly crucial in maintaining a reliable line of communication between alarm systems and monitoring stations.

In terms of technology, the IPGSM-DP utilizes a robust GSM (Global System for Mobile Communications) module for cellular communication. This technology provides high-speed data transmission, which is essential for sending real-time alerts and notifications to security personnel or end-users. This feature enhances the overall responsiveness of the alarm system, enabling swift action in the event of a security breach.

Moreover, the IPGSM-DP is compatible with various alarm control panels, making it a versatile addition to existing security setups. It seamlessly integrates with both Honeywell and third-party systems, allowing users to upgrade their alarm capabilities without overhauling their entire security infrastructure.

The device also boasts advanced encryption technology, which serves to protect the integrity of the communication channels. This security feature is vital in safeguarding sensitive information and ensuring that alarm signals cannot be intercepted or tampered with.

In terms of characteristics, the IPGSM-DP is designed with user-friendliness in mind. It comes with an intuitive LED indicator that provides visual feedback on operational status, signal strength, and any potential issues that may arise. The compact design allows for easy installation in various locations within a property, minimizing disruption to the environment.

Furthermore, the Honeywell IPGSM-DP supports multiple protocols, including Contact ID and SIA, thereby ensuring compatibility with a wide range of monitoring stations and allowing for flexible deployment in diverse security scenarios. Enhanced diagnostic capabilities further simplify troubleshooting and maintenance of the device, ensuring long-term reliability.

In summary, the Honeywell IPGSM-DP is a cutting-edge communication device offering dual-path communication, GSM technology, compatibility with multiple alarm systems, and advanced security features. Its distinctive characteristics make it an excellent choice for enhancing the efficiency and reliability of alarm monitoring and signaling in various security applications.