![](/images/new-backgrounds/1052392/5239253x1.webp)
Installation of Optional Modules | Installation |
2.6.2 4XTMF, 4XLMF and 4XZMF Option Modules
The following steps must be followed when installing each of these modules:
1.Remove all power (AC and DC) from the FACP before installing the modules
2.Cut jumper JP1 (for connectors J3 and J5) and/or JP2 (for connectors J4 and J6) on the main circuit board to allow the control panel to supervise the placement of any installed option module
3.Install the two supplied metal standoffs in the locations indicated. These standoffs provide the required earth ground protection
4.Carefully plug the connectors on the option module into connectors J3 and J5 or J4 and J6 on the FACP main circuit board, being careful not to bend any pins
5.Secure the option module to the standoff on the main circuit board with the supplied screws
6.When the installation has been completed, connect the wiring to the modules as indicated in the following sections
7.Test system for proper operation
TB1 | + | - | + | - | TB2 | B+ B- | B+ | B- | TB3 | B+ | B- | B+ | B- | B+ | B- | B+ | B- | C TRBL NORM | C | NC NOTB6 | C | NC | NO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TB5 |
|
|
|
|
|
| Nonreset | Reset |
| NAC 1 | NAC 2 |
| ZONE 1 ZONE 2 | ZONE 3 ZONE 4 | TROUBLE |
| ALARM |
| SUPV |
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CLASS A |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CONVERTER |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| J1 |
|
|
|
|
|
J3
| ZONE 1 |
|
|
|
FIRE ALARM | SUPERVISORY | TROUBLE | MAINTENANCE | J5 |
|
|
|
|
| ZONE 2 |
|
|
FIRE ALARM | SUPERVISORY | TROUBLE | MAINTENANCE |
| ZONE 3 |
|
|
FIRE ALARM | SUPERVISORY | TROUBLE | MAINTENANCE |
|
|
| ZONE 4 |
|
|
| |
FIRE ALARM | SUPERVISORY | TROUBLE | MAINTENANCE | ||||
AC | NAC | ZONE | NAC | SYSTEM | POWER | WALK | ALARM |
POWER | DISABLE | DISABLE | FAULT | TROUBLE | TROUBLE TEST | SILENCE |
TB7
JP3
Standoffs
J3 (when using
J3 & J5
J5
ms4bord.cdr
TRANSFORMER 2 TRANSFORMER 1
J9
J7
ACK | ALARM | RESET | WALK |
|
|
| SILENCE | ZONE | TEST |
|
|
|
|
|
|
| |
1 | ENABLE/DISABLE | 4 |
|
| |
2 | 3 |
| J4 | ||
|
|
| JP2 | JP1 | J6 |
|
|
|
|
TB8 |
|
| 1 2 | ON | 1 2 | ON | 1 2 | ON |
|
|
| ||||||
| EARTH | CHG | 3 |
| 3 |
| 3 |
|
| J8 |
| 4 5 |
| 4 5 |
| 4 5 |
|
|
|
| 6 |
| 6 |
| 6 |
|
|
|
| 7 |
| 7 |
| 7 |
|
| BATTERY |
| 8 |
| 8 |
| 8 |
|
HOT NEUT EARTH |
| SW1 SW2 | SW3 | |||||
|
|
Standoffs
(when using
J4 J4 & J6
J6
JP2 Jumper | JP1 Jumper |
Cut to install module on J4 & J6 | Cut to install |
| module on J3 & J5 |
Figure 2.12 4X Option Module Connection to MS-4
27 |