Hearth and Home Technologies IDV4833ILH, IDV6247ILT, IDV6247IT Install Vertical Termination Cap

Page 37

H. Install Vertical Termination Cap

•Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section while placing the outer collar of the cap over the outer flue of the pipe section.

•Secure the cap by driving three self-tapping screws (supplied) through the pilot holes in the outer collar of the cap into the outer flue of the pipe).

Termination Cap

Brackets/

 

(1 of three)

 

 

 

Bolts

 

 

Storm

Collar

Screws

Caulk

Figure 10.20

I.Heat Shield Requirements for Horizontal Termination

WARNING! Risk of Fire! To prevent overheating and fire, heat shields must extend through the entire wall thick- ness.

•DO NOT remove the heat shields attached to the wall shield firestop and the horizontal termination cap (shown in Figure 10.26).

•Heat shields must overlap 1-1/2 in. (38 mm) mini- mum.

There are two sections of the heat shield. One section is factory-attached to the wall shield firestop. The other section is factory-attached to the cap. See Figure 10.26.

If the wall thickness does not allow the required 1-1/2 in. (38 mm) heat shield overlap when installed, an extended heat shield must be used.

•If the wall thickness is less than 4 in./102 mm, the heat shields on the cap and wall shield firestop must to be trimmed. A minimum 1-1/2 in. (38 mm) overlap MUST be maintained.

•Use an extended heat shield if the finished wall thickness is greater than 7-1/4 in. (184 mm).

•The extended heat shield may need to be cut to length maintaining sufficient length for a 1-1/2 in. (38 mm) overlap between heat shields.

•Attach the extended heat shield to either of the existing heat shields using the screws supplied with the extended heat shield. Refer to “Vent Components Diagrams” in the back of this manual.

•Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section.

Important Notice: Heat shields may not be field constructed.

Heatilator • ICON DV-IDV Series • 4042-575 • Rev K • 11/08

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents What to do if you smell gas Installation and OperationHomeowner Reference Information CongratulationsInstaller Guide Table of ContentsUser Guide Troubleshooting Hearth & Home Technologies Limited Warranty WarrantyLimited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Operating Instructions Gas Fireplace SafetyYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyClear Space Decorative Doors and FrontsLighting Instructions IPI For Your Safety Read Before LightingInitial Break-in Procedure Frequently Asked QuestionsAfter Fireplace is Lit Maintenance Tasks-Homeowner Maintenance and ServiceMaintenance Tasks-Qualified Service Technician Typical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Any such action may cause a fire hazardSelect Appliance Location Framing and ClearancesModel # Clearances Construct the Appliance ChaseRough Opening Model # Width Height Depth Vent pipe Mantels Mantel and Wall ProjectionsMantel Legs or Wall Projections Vent Termination Minimum Clearances Termination LocationsMinimum Clearances for Termination Approved Pipe Vent Information and DiagramsVent Table Key Use of ElbowsTop Vent Horizontal Termination Vent DiagramsTwo Elbows Two 45 Elbows replacing One 90 ElbowV1 min V1 max H1+H2 max H1+H2+H3 max Three Elbows Installed VerticallyTop Vent Vertical Termination Install Flue RestrictorNo Elbow 12 ft 3.66 m min 60 ft 18.29 m max Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall PenetrationInstalling Ceiling Firestop Install the Ceiling FirestopFlat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Secure and Level the Appliance Appliance PreparationAttach Pipe to the Firebox Assembly Install Vent PipeAssemble Vent Sections Assemble Pipe SectionsSecure the Vent Sections Assemble Slip SectionsDisassemble Vent Sections Install Metal Roof FlashingCaulk 13 Assembling the Storm Collar Assemble and Install Storm CollarSLP-FS Install RF4-8Heat Shield Requirements for Horizontal Termination Install Vertical Termination CapInterior Install Horizontal Termination CapFuel Conversion Gas InformationGas Pressure Gas ConnectionOptional Accessories Requirements Wiring RequirementsIntellifire Ignition System Wiring Electrical Service and RepairRemove Two Screws From Bracket Junction Box InstallationFacing Material FinishingModel Finished Fireplace Opening Noncombustible Finishing MaterialAppliance Setup Placing First Top Log IDV4833 Install the LogsPlace Lava Rock and Rockwool Placement of Rockwool and Lava RockRemoving/Replacing Glass Assembly Glass Panel AssemblyEyelet Rod Support Install Side Refractories Installing External RefractoriesOpen Refractory Package Figure Bottom Front Hearth Refractory24 Air Shutter Adjustment Air Shutter SettingSymptom Possible Cause Corrective Action TroubleshootingIntellifire Ignition System Will not ignite. If the pilot Reference Materials Appliance Dimension DiagramDVP Vent Components Vent Components DiagramsBEK DVP-BEK2 DVP-TVHW Horizontal Termination Cap DVP-TRAPDVP-HRC-SS IDV4833IT, IDV4833IH ÎC. Service PartsIPI Valve Assembly IDV6247IT, IDV6247IH Service PartsIDV6247 Traditional Refractory Pre GA1732717 Post GA1732717 Description Optional ComponentsContact Information

IDV6247ILH, IDV6247IH, IDV4833ILH, IDV4833ILT, IDV6247ILT specifications

Hearth and Home Technologies has established itself as a leader in the hearth industry, offering a range of innovative and efficient products designed for modern living. Among their impressive lineup are the IDV6247IT, IDV4833IT, IDV4833IH, IDV6247ILT, and IDV4833ILT models. These fireplaces are engineered to provide both aesthetic warmth and functional heating, catering to various consumer preferences and home designs.

The IDV6247IT is a remarkable direct vent gas fireplace that offers a spacious viewing area. With its clean lines and contemporary aesthetics, it seamlessly integrates into any living space. Equipped with advanced burner technology, it delivers realistic flames while maximizing efficiency. The model features a variety of customizable options, including remote controls and programmable thermostats, allowing users to tailor their heating preferences to suit their lifestyle.

Similarly, the IDV4833IT and IDV4833IH models offer versatile heating solutions. The IDV4833IT is designed for those seeking a traditional yet modern fireplace experience. With its customizable log sets and flame patterns, it creates a cozy ambiance. The IDV4833IH model distinguishes itself with its enhanced heating capabilities, boasting an impressive BTU output that quickly warms up expansive areas, making it ideal for larger homes.

A notable feature across these models is the innovative IntelliFire technology, which provides reliable ignition and easy operation. This ensures that the fireplace ignites effortlessly, with users able to enjoy the warmth and glow with a simple push of a button. Additionally, the fireplaces utilize a closed combustion system, drawing air from outside, which significantly increases efficiency and reduces heat loss.

For homeowners interested in a more rustic look, the IDV6247ILT and IDV4833ILT models incorporate traditional design elements. These units provide a luxurious feel with their detailed craftsmanship and realistic logs. The high-efficiency design allows for reduced emissions and lower fuel consumption, promoting a more sustainable lifestyle without compromising on warmth or comfort.

In conclusion, Hearth and Home Technologies continues to lead the way in the hearth market with their innovative IDV series. Whether you prefer contemporary elegance or classic charm, models like the IDV6247IT, IDV4833IT, IDV4833IH, IDV6247ILT, and IDV4833ILT deliver not just on style, but also on performance and efficiency. With a focus on user-friendly features and advanced technology, these fireplaces are perfect for any modern home, ensuring a warm and inviting atmosphere for years to come.
Top Page Image Contents