Hearth and Home Technologies SILH30E-B owner manual As an Insert, Pre-installation Preparation

Page 10

B. As an Insert

Pre-installation Preparation

This insert and its components are tested and safe when in- stalled in accordance with this manual. Report to your dealer any parts damaged in shipment, particularly the condition of the glass. Do not install any heater with damaged, in- complete or substitute parts.

WARNING

Fire Risk

•Do not install or operate damaged heater.

•Do not modify heater.

•Installation other than as instructed by Hearth & Home Technologies Inc. is strictly prohibited.

•Do not operate the heater without fully assembling all components.

•Installation and/or use of any component part not approved by Hearth & Home Technologies.

Hearth & Home Technologies disclaims any responsibility for, and the warranty and agency listing will be voided by the above actions.

•A retaining method may be needed to secure the heater in place.

•Combustible facing material may be installed over the original combustible or noncombustible facing material on the solid fuel fi replace. The original specifi ed clearances of a factory-built fireplace must be maintained, with the exception of the hearth. Clearances on a masonry fi replace must be maintained at 12 in. from the opening for combustible projections over 1-1/2 in. Clearances for combustible projections under 1-1/2 in. must be maintained per NFPA 211. Plan the surround size accordingly. A front face must be used with the insert.

•The insert front face is tested and approved with this insert and may cover existing air circulation vents or grilles on the solid fuel fi replace it is installed into. Should the face not cover the entire ventilation grille surface, the grille should be left open.

•The solid fuel fi replace’s fl ue damper must be fully locked in the closed position or removed for installation.

Note: Decorative trim front faces have been tested and approved to cover existing air circulation vents or grills.

•The chimney must be capped.

•Install the insert without the front face and make all electrical connections.

Installation

•These inserts are designed for installations into solid fuel masonry or factory built noncombustible fi replaces that have been installed in accordance with the national, provincial, state or local building codes.

•You should seal off the area between the termination cap and the top of the existing chimney opening to avoid down drafts, moisture and/or cold air problems.

•Minimum fi replace opening requirements are shown in Figures 3.1 and 3.2 of this installation manual. The firebrick (refractory) can be removed from a factory built fi replace in order to gain minimum insert opening requirements.

•This insert requires no hearth extensions. Combustible material on the floor may be installed up to the insert. Do not obstruct the lower grill of the insert. The original fi replace cannot be returned to solid fuel in this condition.

•The metal fl oor of the solid fuel fi rebox may be removed to facilitate the installation of the insert. The side walls and top structure of the fi rebox may not be altered with the exception of removable baffl es and dampers. The original fi replace cannot be returned to solid fuel in this condition.

•Position, Level and Secure Insert

•Place the heater into position.

•Level the heater from side to side and from front to back. If necessary, use the leveling bolts included in the manual bag. Screw the bolts into the nuts installed in the bottom of the insert (see replacement parts diagram). Turn bolts in until the insert is level.

Note: The warning label above, located in the instruction package, must be affi xed to the lower back wall of the existing fi replace prior to installation of the insert.

Note: When the front is installed it will cover the gap between the heater and the framing, cabinet, finishing materials or existing fi replace.

10

Heatilator • SILH30E-B • 4038-896 Rev C • 11/05

Page 9 Page 11
Image 10
Page 9 Page 11
Contents SILH30E-B Homeowner Reference Information Listing Label Information/LocationTable of Contents Important Instructions Listing and Code ApprovalsCertification Not intended for use as a primary heat sourceGetting Started Tools and Supplies NeededClearances Framing and ClearancesSelecting Heater Location Electrocution RiskModel Frame the Heater Framing the HeaterShock Risk InstallationAs a Fireplace Shock Risk Fire RiskPre-installation Preparation As an InsertWiring RW RT Install the Front Face AccessoriesInstall other Optional Accessories Finishing Material Finishing ChecklistFinishing MantelOperating Instructions Main Power SwitchThermostat Troubleshooting Troubleshooting GuideClean the Firebox Compartment Maintenance and ServiceAccess the Firebox Clean the Back Acrylic PanelMaintenance Task List When cleaning glass doorHeater Dimensions Reference MaterialsPBT = Polished Brass Trim Optional ComponentsSST = Stainless Steel Trim Service Parts SILH30E-BThermostat Control Assembly Hearth Assembly Ember BedLog Assembly # Description of PartWarranty Limited WarrantyContact Information

SILH30E-B specifications

Hearth and Home Technologies SILH30E-B is an innovative direct vent gas fireplace that combines modern aesthetics with advanced functionality, making it an ideal choice for homeowners who seek both beauty and efficiency. This stylish unit features a sleek design with a large glass front, allowing for an unobstructed view of the flames. The SILH30E-B effortlessly blends into various interior settings, from contemporary to traditional, enhancing the overall ambiance of any room.

One of the standout features of the SILH30E-B is its energy efficiency. This fireplace is designed to maximize heat output while minimizing energy consumption, making it an environmentally friendly choice for heating spaces. The direct vent technology allows the unit to draw air from the outside for combustion, ensuring that the indoor air quality remains unaffected while providing optimal heating performance. This system also eliminates the need for a traditional chimney, simplifying installation and maintenance.

The SILH30E-B boasts a range of customizable options. Homeowners can select from various media types, including glass and stones, to personalize the fireplace's appearance. Additionally, the adjustable flame height feature allows users to create the perfect ambiance, whether they prefer a cozy fire for intimate gatherings or a roaring flame to warm up the entire space. This unit also includes a programmable remote control, granting easy access to the fireplace's settings from anywhere in the room.

Safety is a top priority for Hearth and Home Technologies, and the SILH30E-B incorporates several safety features. The unit is equipped with an automatic shut-off system that activates in case of irregularities, ensuring peace of mind for users. The cool-to-the-touch glass front prevents accidental burns, making it a suitable option for homes with children or pets.

In terms of installation, the SILH30E-B is designed for versatility. It can be installed as a built-in unit or as a zero-clearance fireplace, accommodating various architectural layouts and personal preferences. Its high-quality construction materials and advanced technologies further contribute to its durability and longevity, assuring homeowners of a sound investment.

In summary, the Hearth and Home Technologies SILH30E-B symbolizes the perfect merger of style, efficiency, and safety. With its modern design, customizable features, and energy-efficient performance, it stands out as a leading option for those looking to enhance their living spaces with a reliable and beautiful fireplace solution.
Top Page Image Contents