Hearth and Home Technologies COLBAY-INS owner manual Grille Installation, Panel Set Installation

Page 17

D. Grille Installation

Remove the door of appliance. Remove the four screws (two at each end) holding grille in place. Lift up to remove.

Assemble the trim with the two corner brackets provided. Slide the assembled trim over the assembled panel set.

Figure 8.5

Install the new grille by reversing removal instructions.

Note: Clean glass and gold or nickel with glass cleaner and a soft cloth, wiping off all fingerprints prior to first fire to prevent permanent staining.

E. Panel Set Installation

Included in kit: (2) Angle Brackets and set screws; (1) 3 piece Trim; (2) Side Panels; (1) Top Panel; (1) Switch plug; and (8) screws.

Tools required: Philips head screwdriver.

Note: Remove the door from the insert before beginning the panel installation.

Assemble the panel top to the panel sides with the screws provided.

BACK OF TOP PANEL

SCREWS

BACK OF SIDE PANEL

Figure 8.6

Figure 8.7

Slide the panel/trim down over the face of the unit, behind the top, aligning the holes in the upper and lower, right and left corners, and secure the panel and trim set to the appliance with the attachment screws using four screws, two per side.

SCREWS

Figure 8.8

Determine your desired placement of the rocker switch.

1If you wish to place it on the control panel in the "Main Burner" opening: Disconnect the "ON/OFF" switch from the low voltage wire leads. Pull the wires through the control panel, attach the wires to the "ON/OFF" rocker switch and push the rocker switch into the "Main Burner opening on control panel. Place the plug provided in empty opening on the panel and trim.

OR

2.If you wish to place it on the side of appliance in the knock out provided on the panel and trim: Carefully reposition the wiring beneath the firebox to the RIGHT side of appliance. Disconnect the "ON/OFF" switch from the low voltage wire leads. Pull the wires through the knockout plate on the panel and trim, attach the wires to the "ON/OFF" rocker switch and push the rocker switch into the opening on the panel and trim. Place plug provided with panel set in empty switch location.

Install the power cord restraint found in the appliance com- ponent bag. (Cord is shipped exiting the right side of the appliance, but can be routed in either direction.) A notch will be needed in the trim piece for the cord restraint.

Slide the appliance back until the panel is tight to the fireplace.

Quadra-Fire • Columbia Bay Insert • 7002-109 Rev. H • 10/08

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Do Discardnot What to do if you smell gasCOLBAY-INS Welcome to the Quadra-Fire Family Table of Contents Listing and Code Approvals Tools and Supplies Needed Installation to ensure maximum safety and benefitGetting Started Selecting Appliance Location Framing and ClearancesClearances to Combustibles HearthVent Termination Minimum Clearances Termination LocationsVent Information Venting and InstallationExhaust AIR Vent Pipe Termination CAP Adaptor Converting to LP Gas Gas InformationFuel Conversions Valve Regulator Replacement Gas Connection Gas PressuresHigh Altitude Installations Connecting to the Appliance Recommendation for WireStanding Pilot Ignition System Wiring Wire Size Max. LengthPilot Accessories Appliance SetupDoor Crown Installation Remove Shipping MaterialsBack of TOP Panel Screws Back of Side Panel Grille InstallationPanel Set Installation Baffle Supports Brick InstallationBaffle Rear Brick Panel Brick ClipsPositioning the Logs Included in kit Blower Blower InstallationMineral Wool = 1/4 in mm female spade = 1/4 in mm male spade Air Shutter Adjustment Before Lighting Appliance Operating InstructionsLighting Appliance For Your Safety Read Before LightingAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action TroubleshootingDoor Frame with Glass Assembly Replacement Glass ReplacementMaintaining and Servicing Appliance To Replace Separate Glass PiecesNecessary. USE Caution When CLEANING/HANDLING Ceramic Burner Maintenance Tasks InspectReference Materials Appliance Dimension DiagramHHT Vent Components ListService Parts Log Set AssemblyStocked At Depot Service Parts ListDescription Serial # Part Number Bottom Firebox AssemblyCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

COLBAY-INS specifications

Hearth and Home Technologies (HHT) has made significant strides in the hearth industry, and one of its standout offerings is the COLBAY-INS. This innovative indoor fireplace embodies the company's commitment to quality, efficiency, and design flexibility, catering to modern homeowners seeking a spectacular focal point for their living spaces.

The COLBAY-INS integrates state-of-the-art technology with elegant design. One of its most remarkable features is the advanced heat management system that optimally distributes warmth throughout the room. By utilizing a powerful, efficiency-driven heating mechanism, the COLBAY-INS ensures that energy consumption is minimized while still providing exceptional warmth. With an impressive thermal efficiency rating, it combines comfort and sustainability, making it an excellent choice for modern homes.

Another distinguishing characteristic of the COLBAY-INS is its large viewing area. The expansive glass front allows for an unobstructed view of the flames, creating a captivating ambiance that transforms any indoor setting. This allows homeowners to enjoy the aesthetic appeal of a traditional fire without the hassle and mess associated with wood-burning fireplaces. The glass is designed to be heat-resistant and easy to clean, ensuring that the beauty of the flames remains the focal point.

The COLBAY-INS also incorporates smart technology for enhanced user convenience. With options for remote operation and smart home integration, users can easily control the fireplace's settings from their smartphones or smart devices. This feature not only adds a layer of comfort but also allows for seamless integration into all home automation systems.

Safety is paramount in the design of the COLBAY-INS. It includes multiple safety features, such as a secure door mechanism that keeps flames contained and a built-in safety shut-off function that activates in the event of an overheating situation. The overall construction adheres to the highest safety standards, giving homeowners peace of mind.

Moreover, the COLBAY-INS offers a variety of customization options, including different hearth finishes and media beds. This ensures that it can beautifully complement any interior design theme, from sleek contemporary to rustic charm. Additionally, the dual-fuel capability allows users to choose between natural gas and propane, providing flexibility based on personal preferences and availability.

In summary, Hearth and Home Technologies' COLBAY-INS is an exceptional indoor fireplace that combines efficient heating, modern technology, and stylish design. With its impressive features, safety standards, and customization options, it serves as a beautiful centerpiece while enhancing the overall comfort of any home.
Top Page Image Contents