Hearth and Home Technologies GARNET-D-CWL Type B Rear Installations for Use with Rear Vent Kit

Page 12

F. Horizontal Termination

Type A - Up & Out Installations for Top Vent Configurations

90º ELBOW center line

PIPE LENGTH

TERMINATION CAP

 

 

WALL THIMBLE

WALL THIMBLE COVER

PIPE LENGTH

Type B - Rear Installations for Use with Rear Vent Kit

CENTER LINE

17-3/4 in.

 

(451mm)

TERMINATION CAP

WALL THIMBLE

WALL THIMBLE COVER

Type C - 45° Elbow in Corner Installation

 

Wall Thimble

45° Elbow

2 in. (51mm)

 

Clearance from stove

 

corner to combustible

 

wall

2 in. (51mm) Clearance from stove corner to combustible wall.

Figure 5.3

Step 1.

Determine the desired location of the appliance. Check to ensure that wall studs or roof rafters are not in the way when the venting system is attached. If this is the case, you may want to adjust the location of the appliance.

WARNING

Fire Hazard.

Exhaust Fume Risk.

Impaired Performance of Appliance.

•Ensure vent components are locked together correctly.

•Pipe may separate if not properly joined.

Step 1.

Determine the desired location of the appliance. Check to ensure that wall studs or roof rafters are not in the way when the venting system is attached. If this is the case, you may want to adjust the location of the appliance.

Step 2.

Direct vent pipe is designed with a locking connection. To connect the venting system to the appliance flue outlet, a twist-lock adapter is built into the appliance at the factory. Wall thickness may vary. Remember to include wall thickness in minimum clearances when figuring venting lengths for your installation needs.

Note: Female ends of direct vent pipe/elbows are designed to slide straight onto the male ends of adjacent pipes by orienting the pipe indentations so they match and slide into the entry slots on the male ends, see Figure 5.4. Push the pipe sections completely together, then twist-lock one section clockwise approximately one-quarter turn, until the two sections are fully locked. The female locking lugs may not be visible from the outside. They may be located by examining the inside of the female ends.

Female Locking Lugs

Male Locking Lugs

Figure 5.4

Page 12

Quadra-Fire · Garnet-T · 7016-127F

September 1, 2008

Page 11 Page 13
Image 12
Page 11 Page 13
Contents What to do if you smell gas Do not Discard this ManualDo Discardnot Hot glass will cause burnsSerial Number Model Name Test Lab & Report No Manufactured DateTable of Contents 1Listing and Code Approvals Requirements for the Commonwealth of Massachusetts BELOW. Keep Clear of ALL ObstructionsManufacturer Requirements Tools will apply to every installation Getting StartedTools and Supplies Needed Selecting Appliance Location Clearances4Termination Locations Vent Termination Minimum ClearancesAlcove Applications Vent Information Venting Components Use of ElbowsMeasuring Standards Do not USE FIELD-FABRICATED VentingHow to Use the Vent Graph Venting Guidelines Exceptions For Horizontal InstallationsType B Rear Installations for Use with Rear Vent Kit StepFire Risk. Explosion Risk. Combustion Fume Risk 203mm Vertical Termination Direct Vent PipeStep Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Existing Masonry Chimney Type D Hearth MountType B Cut and bend flashing as needed to fit Sealant adhesive Retro Connector Installing Slim Line Trim Ring and Heat Shield Slim Line Wall ThimbleBefore YOU Begin Assembling Slim Line Trim Ring and Heat ShieldTrim Ring Gas Information Fuel ConversionsConverting to LP Gas Propane Natural GASValve Regulator Replacement Gas Pressures Gas Connection PressureCheck for GAS Leaks Recommendation for Wire Connecting to the ApplianceStanding Pilot Ignition System Wiring Wire Size Max. LengthIgnition Module Appliance Setup Flue Restrictor InstallationRemove Shipping Materials Leg Leveling SystemAccessories Positioning the LogsMineral Wool Glass Replacement Blower InstallationKIT Contents Snap Disc White Ignition Module Access and Battery Replacement Shutter AdjustmentIntake Damper Operation Operating Instructions Before Lighting ApplianceControls For Your Safety Read Before Lighting Lighting ApplianceFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Cause Corrective ActionBe Placed in this Opening Maintaining and Servicing Your Appliance After servicingMaintenance Tasks Inspect Necessary. USE Caution When CLEANING/HANDLING Ceramic BurnerAppliance Dimension Diagram Reference MaterialsVent Components Diagram Mm inner pipe 6-5/8 in mm outer pipeSeptember 1 Quadra-Fire · Garnet-T · 7016-127F Vent Components List HHT SL-PTermination Caps & Kits GARNET-T DescriptionService Parts List cont’d. GARNET-T Service Parts List cont’d. GARNET-T Accessories Service And Maintenance Log Date of Service Performed By Description of ServiceHomeowner’s Notes Warranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Garnet-T Contact InformationDealer Telephone

GARNET-D-CSB, GARNET-D-CWL, GARNET-MBK, GARNET-D-PMH, GARNET-D-MBK specifications

Hearth and Home Technologies has a reputation for excellence in the home heating and comfort industry, offering a range of top-tier products that combine modern design with functionality. Among their esteemed offerings are the GARNET-D-MBK, GARNET-D-PMH, GARNET-MBK, GARNET-D-CWL, and GARNET-D-CSB units, each designed to meet diverse consumer preferences while promoting efficiency and style.

The GARNET-D-MBK model, characterized by its sleek black finish, seamlessly integrates into contemporary living spaces. It boasts an efficient heating system that utilizes advanced combustion technology to maximize heat output while minimizing emissions. Its easy-to-use interface ensures users can control the device with minimal effort, making it ideal for both seasoned and first-time stove owners.

In contrast, the GARNET-D-PMH features a polished mahogany finish that appeals to those wanting a classic aesthetic. This model incorporates cutting-edge burn technology, which not only enhances heat retention but also significantly reduces the time required to achieve optimal temperatures. With its thoughtful design and craftsmanship, the GARNET-D-PMH stands as a beautiful centerpiece in any room.

Moving on to the GARNET-MBK, this model offers the same high efficiency as its counterparts with an added advantage of a modular design. This adaptability allows homeowners to customize the unit based on their specific space requirements. Its multiple heating settings cater well to varying temperatures, contributing to its reputation as an energy-efficient alternative.

The GARNET-D-CWL model is distinguished by its compact design and rugged construction. This product was engineered for utility while maintaining aesthetic appeal. The unit’s innovative technology not only ensures impressive heat output but also incorporates safety features that make it a reliable choice for families.

Lastly, the GARNET-D-CSB encapsulates the essence of versatility. This model effortlessly balances function and design, featuring an elegant coating that enhances durability. Its digital controls offer precision in temperature management, while its efficient energy use aligns with modern environmental standards.

Across all these models, Hearth and Home Technologies prioritizes quality, utilizing durable materials and state-of-the-art engineering techniques. Their commitment to customer satisfaction and environmental responsibility is evident in every unit, making these garnet series products standout choices for effective home heating solutions.
Top Page Image Contents