Hearth and Home Technologies GARNET-D-PMH, GARNET-D-CSB, GARNET-MBK 1Listing and Code Approvals

Page 4

1Listing and Code Approvals

A. Appliance Certification

C. BTU Specifications

 

MODEL:

Garnet-T

LABORATORY:

OMNI Test Laboratories, Inc.

 

061-S-35c-5

TYPE:

Direct Vent Gas Heater

STANDARD:

ANSI Z21.88a-2003ּCSA 2.33a-2003ּ

 

UL307bּCAN/CBA 2.17-M91

Model

Maximum

Minimum

Orifice

*Steady

**P.4

Input

Input

Size

State %

%

(US or Canada)

BTU

BTU

(DMS)

 

 

 

 

 

Garnet-T (NG)

17,000

12,000

49

76.93

67.38

Garnet-T (LP)

17,000

13,000

56

78.19

69.52

*Thermal efficiency maximum pipe with blower on. ** Canada minimum pipe.

The product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recre- ational Vehicles” and "Gas Fired Appliances for use at High Altitudes".

Manufactured Home or Mobile Home installation may occur only after the home is site located and must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4.

When installed, the appliance must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

B. Glass Specifications

This appliance is equipped with 5mm ceramic glass. Replace glass only with 5mm ceramic glass. Please contact your dealer for replacement glass.

D. High Altitude Installations

Omni-Test Laboratories listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and 0 to 4500 feet in Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

E. Non-Combustible Materials

Materials that are reported as passing ASTM E 136, Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C, shall be considered non-combustible materials.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

F. Combustible Materials

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other materials that can ignite and burn, whether flame proofed or not, or whether plastered or unplastered shall be considered combustible materials.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the unit and to replace any part of the control system and any gas control which has been under water.

Page 4

Quadra-Fire · Garnet-T · 7016-127F

September 1, 2008

Image 4
Contents What to do if you smell gas Do not Discard this ManualDo Discardnot Hot glass will cause burnsSerial Number Model Name Test Lab & Report No Manufactured DateTable of Contents 1Listing and Code Approvals BELOW. Keep Clear of ALL Obstructions Requirements for the Commonwealth of MassachusettsManufacturer Requirements Getting Started Tools will apply to every installationTools and Supplies Needed Selecting Appliance Location Clearances4Termination Locations Vent Termination Minimum ClearancesAlcove Applications Vent Information Venting Components Use of ElbowsMeasuring Standards Do not USE FIELD-FABRICATED VentingHow to Use the Vent Graph Venting Guidelines Exceptions For Horizontal InstallationsType B Rear Installations for Use with Rear Vent Kit StepFire Risk. Explosion Risk. Combustion Fume Risk 203mm Vertical Termination Direct Vent PipeStep Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Type D Hearth Mount Existing Masonry ChimneyType B Cut and bend flashing as needed to fit Sealant adhesive Retro Connector Installing Slim Line Trim Ring and Heat Shield Slim Line Wall ThimbleBefore YOU Begin Assembling Slim Line Trim Ring and Heat ShieldTrim Ring Gas Information Fuel ConversionsConverting to LP Gas Propane Natural GASValve Regulator Replacement Gas Pressures Gas Connection PressureCheck for GAS Leaks Recommendation for Wire Connecting to the ApplianceStanding Pilot Ignition System Wiring Wire Size Max. LengthIgnition Module Appliance Setup Flue Restrictor InstallationRemove Shipping Materials Leg Leveling SystemPositioning the Logs AccessoriesMineral Wool Blower Installation Glass ReplacementKIT Contents Snap Disc White Shutter Adjustment Ignition Module Access and Battery ReplacementIntake Damper Operation Before Lighting Appliance Operating InstructionsControls For Your Safety Read Before Lighting Lighting ApplianceInitial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Troubleshooting Symptom Possible Cause Corrective ActionBe Placed in this Opening Maintaining and Servicing Your Appliance After servicingMaintenance Tasks Inspect Necessary. USE Caution When CLEANING/HANDLING Ceramic BurnerAppliance Dimension Diagram Reference MaterialsMm inner pipe 6-5/8 in mm outer pipe Vent Components DiagramSeptember 1 Quadra-Fire · Garnet-T · 7016-127F Vent Components List HHT SL-PTermination Caps & Kits GARNET-T DescriptionService Parts List cont’d. GARNET-T Service Parts List cont’d. GARNET-T Accessories Service And Maintenance Log Date of Service Performed By Description of ServiceHomeowner’s Notes Warranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Contact Information Garnet-TDealer Telephone

GARNET-D-CSB, GARNET-D-CWL, GARNET-MBK, GARNET-D-PMH, GARNET-D-MBK specifications

Hearth and Home Technologies has a reputation for excellence in the home heating and comfort industry, offering a range of top-tier products that combine modern design with functionality. Among their esteemed offerings are the GARNET-D-MBK, GARNET-D-PMH, GARNET-MBK, GARNET-D-CWL, and GARNET-D-CSB units, each designed to meet diverse consumer preferences while promoting efficiency and style.

The GARNET-D-MBK model, characterized by its sleek black finish, seamlessly integrates into contemporary living spaces. It boasts an efficient heating system that utilizes advanced combustion technology to maximize heat output while minimizing emissions. Its easy-to-use interface ensures users can control the device with minimal effort, making it ideal for both seasoned and first-time stove owners.

In contrast, the GARNET-D-PMH features a polished mahogany finish that appeals to those wanting a classic aesthetic. This model incorporates cutting-edge burn technology, which not only enhances heat retention but also significantly reduces the time required to achieve optimal temperatures. With its thoughtful design and craftsmanship, the GARNET-D-PMH stands as a beautiful centerpiece in any room.

Moving on to the GARNET-MBK, this model offers the same high efficiency as its counterparts with an added advantage of a modular design. This adaptability allows homeowners to customize the unit based on their specific space requirements. Its multiple heating settings cater well to varying temperatures, contributing to its reputation as an energy-efficient alternative.

The GARNET-D-CWL model is distinguished by its compact design and rugged construction. This product was engineered for utility while maintaining aesthetic appeal. The unit’s innovative technology not only ensures impressive heat output but also incorporates safety features that make it a reliable choice for families.

Lastly, the GARNET-D-CSB encapsulates the essence of versatility. This model effortlessly balances function and design, featuring an elegant coating that enhances durability. Its digital controls offer precision in temperature management, while its efficient energy use aligns with modern environmental standards.

Across all these models, Hearth and Home Technologies prioritizes quality, utilizing durable materials and state-of-the-art engineering techniques. Their commitment to customer satisfaction and environmental responsibility is evident in every unit, making these garnet series products standout choices for effective home heating solutions.