Hearth and Home Technologies FB-ZC-S owner manual Installation Preparation

Page 11

6 Installation Preparation

Prepare the existing solid fuel masonry or factory built non-combustible firebox for installation.

A. Flue Damper

Fully lock the solid fuel fireplace’s flue damper in the open position, OR completely remove it.

E. Fireplace Conversion Notice

Permanently attach the label with the following warning to the inside lower back of the fireplace firebox into which the insert is being installed. Silicone may be required to properly secure the label.

B. Chimney

•Ensure chimney is constructed of non-combustible materials.

•Ensure chimney is clean and in good working order.

•Ensure that all chimney cleanouts fit properly to prevent air leakage into chimney.

C. Gas Line

Note: If the factory built fireplace has no gas access hole provided, an access hole of 1 inch (25 mm) diameter or less may be drilled through the lower sides or bottom of the firebox in a proper workmanship - like manner. This access hole must be plugged with non-combustible insulation after the gas supply line has been installed.

•Install gas line into firebox cavity.

•Check local codes and gas line sizing requirements following NFPA54. See Section 8.

WARNING

Fire Risk.

This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the fireplace re- approved by the authority having jurisdiction.

Prior to installing the gas insert:

•Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certi- fied professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.

•Replace component parts of the chimney and fireplace as specified by the professionals.

•Ensure all joints are properly engaged and the chimney is properly secured.

D. Hearth or Hearth Extension

WARNING

Fire Risk.

A hearth or hearth extension (if present) must comply with either of the following:

•The solid fuel burning fireplace manufacturer’s specification.

• Local building codes required by authority having jurisdiction.

• NFPA 211

F. Remote Control

The receiver for the remotes must be installed BETWEEN the base pan of the insert and the firebox of the wood- burning fireplace (see photo below).

EXISTING SIDE

REFRACTORY

REMOTE

RECEIVER

UNIT

EXISTING BOTTOM OF

FIREPLACE

Heat & Glo • FB-ZC-S • 2019-910 Rev. G • 11/08

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents What to do if you smell gas ModelHomeowner Reference Information CongratulationsTable of Contents Listing and Code Approvals Tools and Supplies Needed Design and Installation ConsiderationsGetting Started Inspect Appliance and ComponentsInspect Firebox Minimum Fireplace Opening Fireplace Size RequirementsClearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsMeasuring Standards Vent Information and DiagramsVent Table Key Horizontal VentingInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Class a Wood Pipe Inlet AIR Vent Pipe Stainless Steel Placing, Securing and Leveling the Appliance Damper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Wood BurningGas Pressures Gas InformationFuel Conversions Gas Connection High Altitude Installations Appliance Requirements Wiring the ApplianceON/OFF Switch Electrical InformationOptional Accessories Junction Box InstallationInstallation for Fan Optional Fan Wiring Diagram Mantel Projections FinishingEmber Placement Appliance SetupClean the Appliance AccessoriesPositioning the Logs Log Set Assembly LOGS-FB-ZCGroove Replacing Glass Assembly Glass AssemblyAir Shutter Setting Removing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance Standing Pilot Ignition Lighting ApplianceAfter Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Issue Solutions Frequently Asked QuestionsStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action TroubleshootingMaintaining and Servicing Appliance Maintenance TasksDoors, Surrounds Inspect Maintenance TasksReference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsPart number list on following Log Set AssemblyService Parts At Depot Service Parts ListStocked Service Parts Valve AssemblyCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

FB-ZC-S specifications

Hearth and Home Technologies has consistently been at the forefront of innovative heating solutions, and the FB-ZC-S is a prime example of their dedication to quality and performance. This gas fireplace has been designed not only for aesthetic appeal but also for optimal functionality, making it an excellent choice for modern homes.

One of the standout features of the FB-ZC-S is its impressive heating efficiency. Utilizing advanced gas technology, this fireplace ensures a high rate of heat output while maintaining low emissions. Homeowners will appreciate the efficient use of fuel, which translates into cost savings on energy bills. The FB-ZC-S is capable of producing a significant amount of heat, making it suitable for larger spaces.

The design of the FB-ZC-S is another highlight, featuring a sleek, contemporary look that fits well with a variety of interior styles. Its clean lines and minimalist approach allow it to blend seamlessly into any living area while serving as a stunning focal point. The unit comes with a variety of customizable options, including different front styles, decorative media, and trim finishes, enabling homeowners to personalize their fireplace according to their tastes.

Hearth and Home Technologies has equipped the FB-ZC-S with state-of-the-art technologies, including an easy-to-use control system. The intuitive interface allows users to adjust the flame height and heat output with ease, providing the ultimate comfort at their fingertips. Additionally, the fireplace can be integrated with smart home systems, enabling users to control their heating from anywhere, whether via smartphone or voice commands.

Further enhancing its appeal, the FB-ZC-S features a direct vent system that offers safe and efficient operation. This system allows for the expulsion of combustion gases outside the home while drawing in outside air for combustion, thus maintaining indoor air quality. Safety is paramount, and the FB-ZC-S is built with multiple safety features, including automatic shut-off systems and high-temperature safety locks.

In summary, the Hearth and Home Technologies FB-ZC-S is a state-of-the-art gas fireplace that blends modern design with advanced heating technology. Its impressive efficiency, customizable options, user-friendly controls, and safety features make it a standout choice for homeowners looking to enhance their living space with effective and stylish warmth. Whether for cozy family gatherings or serene evenings at home, the FB-ZC-S is designed to provide both comfort and charm.
Top Page Image Contents