Hearth and Home Technologies FB-ZC-S owner manual Gas Information, Fuel Conversions Gas Connection

Page 16

8 Gas Information

A. Fuel Conversions

C. Gas Connection

Before making gas connections ensure that appliance be- ing installed is compatible with the available gas type.

Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified and approved parts.

Note: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI

223.1.Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).

B. Gas Pressures

Proper input pressures are required for optimum appli- ance performance. Gas line sizing requirements need to be made following NFPA54.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

•Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

WARNING

Verify inlet pressures.

• High pressure may cause overfire condition.

• Low pressure may cause explosion.

•Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

Pressure requirements for appliance are shown in the table below. Minimum pressures must be met when other household gas appliances are operating.

Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 inches

11.0 inches

w.c.

w.c.

 

Maximum inlet gas pressure

14.0 inches

14.0 inches

w.c.

w.c.

 

Manifold pressure

3.5 inches

10.0 inches

w.c.

w.c.

 

NOTE: A listed (and Commonwealth of Massachusetts ap- proved) 1/2 inch (13 mm) T-handle manual shut-off valve and flexible gas connector are connected to the 1/2 inch (13 mm) control valve inlet.

•If substituting for these components, please consult local codes for compliance.

Refer to Section 15 for location of gas line access in ap- pliance.

NOTE: Gas line may be run from either side of the appliance provided the hole in the outer wrap does NOT exceed 2-1/2 inches in diameter and does not penetrate the firebox.

WARNING

Gas Leak Risk

•Support control when attaching pipe to prevent bending gas line.

NOTE: The gap between supply piping and gas access hole may be caulked with high temperature caulk or stuffed with non-combustible, unfaced insulation to prevent cold air infiltration.

•Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes.

•Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve.

•Check all fittings and connections of appliance which may have loosened during shipping.

16

Heat & Glo • FB-ZC-S • 2019-910 Rev. G • 11/08

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Design and Installation Considerations Getting StartedInspect Appliance and Components Tools and Supplies NeededInspect Firebox Fireplace Size Requirements Minimum Fireplace OpeningClearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent Information and Diagrams Vent Table KeyHorizontal Venting Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Class a Wood Pipe Inlet AIR Vent Pipe Stainless Steel Placing, Securing and Leveling the Appliance Installing Adaptor and Termination Cap MasonryFactory Built Wood Burning Damper Flashing Kit OptionalFuel Conversions Gas Connection Gas InformationGas Pressures High Altitude Installations Wiring the Appliance ON/OFF SwitchElectrical Information Appliance RequirementsInstallation for Fan Optional Junction Box InstallationOptional Accessories Fan Wiring Diagram Finishing Mantel ProjectionsAppliance Setup Clean the ApplianceAccessories Ember PlacementLog Set Assembly LOGS-FB-ZC Positioning the LogsGroove Glass Assembly Air Shutter SettingRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsBefore operating this appliance have a qualified technician Lighting Appliance Standing Pilot IgnitionCheck Pilot Flame Appearance Initial Break-in ProcedureAfter Appliance is Lit Frequently Asked Questions Issue SolutionsSymptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsService Parts Log Set AssemblyPart number list on following Stocked Service Parts ListAt Depot Valve Assembly Service PartsCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

FB-ZC-S specifications

Hearth and Home Technologies has consistently been at the forefront of innovative heating solutions, and the FB-ZC-S is a prime example of their dedication to quality and performance. This gas fireplace has been designed not only for aesthetic appeal but also for optimal functionality, making it an excellent choice for modern homes.

One of the standout features of the FB-ZC-S is its impressive heating efficiency. Utilizing advanced gas technology, this fireplace ensures a high rate of heat output while maintaining low emissions. Homeowners will appreciate the efficient use of fuel, which translates into cost savings on energy bills. The FB-ZC-S is capable of producing a significant amount of heat, making it suitable for larger spaces.

The design of the FB-ZC-S is another highlight, featuring a sleek, contemporary look that fits well with a variety of interior styles. Its clean lines and minimalist approach allow it to blend seamlessly into any living area while serving as a stunning focal point. The unit comes with a variety of customizable options, including different front styles, decorative media, and trim finishes, enabling homeowners to personalize their fireplace according to their tastes.

Hearth and Home Technologies has equipped the FB-ZC-S with state-of-the-art technologies, including an easy-to-use control system. The intuitive interface allows users to adjust the flame height and heat output with ease, providing the ultimate comfort at their fingertips. Additionally, the fireplace can be integrated with smart home systems, enabling users to control their heating from anywhere, whether via smartphone or voice commands.

Further enhancing its appeal, the FB-ZC-S features a direct vent system that offers safe and efficient operation. This system allows for the expulsion of combustion gases outside the home while drawing in outside air for combustion, thus maintaining indoor air quality. Safety is paramount, and the FB-ZC-S is built with multiple safety features, including automatic shut-off systems and high-temperature safety locks.

In summary, the Hearth and Home Technologies FB-ZC-S is a state-of-the-art gas fireplace that blends modern design with advanced heating technology. Its impressive efficiency, customizable options, user-friendly controls, and safety features make it a standout choice for homeowners looking to enhance their living space with effective and stylish warmth. Whether for cozy family gatherings or serene evenings at home, the FB-ZC-S is designed to provide both comfort and charm.
Top Page Image Contents