Hearth and Home Technologies FB-ZC-S owner manual Placing, Securing and Leveling the Appliance

Page 14

CUT AND BEND

FLASHING AS NEEDED

TO FIT CHIMNEY

SEALANT

ADHESIVE

Figure 7.2

•Trim chimney top plate to minimize excess overhang or bend over flue tile (see Figure 7.2).

•Place 3/8 inch bead of 300º F silicone on flue tile top.

C.Placing, Securing and Leveling the Appliance

•Install insert (without surround attached) into existing fireplace while pulling collar slide plate forward.

•Install gas line into hole provided on insert side.

•If applicable install remote control wires into insert side (see Section 6, F.).

•Secure collar slide plate to appliance by placing locking handle into position with locking tabs (see Figure 7.1) and secure with #8 screw.

•Level the appliance from side to side and front to back. If necessary, use the leveling legs included with the manual bag to set each corner of the base.

•Position any excess flexible vent pipe back up into chimney without sagging. Twist and push flex vent together to shorten.

•Install fiberglass insulation pieces to back face of surround.

•Attach surround. Follow instructions accompanying surround.

•Push insert so that surround becomes tight against face of fireplace.

WARNING

Fire Risk.

Only an approved Hearth & Home Technologies surround may be used to cover integral grills on solid fuel burning fireplaces.

• No other components such as shrouds, sheet- metal plates, etc., may be used to seal off vents.

WARNING

Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

WARNING

Explosion Risk.

Combustion Fume Risk.

•Connect vent sections per installation instructions.

•The 3 foot section of stainless steel flexible pipe MUST be attached directly to the exhaust collar on the collar slide plate.

•Connect exhaust vent pipe ONLY to exhaust starting collar and termination cap center collar.

•Connect inlet air vent ONLY to inlet air collar on appliance and either the termination cap inlet air collar OR terminate within chimney.

•Do NOT allow vent to sag below connection point to appliance.

14

Heat & Glo • FB-ZC-S • 2019-910 Rev. G • 11/08

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Inspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededInspect Firebox Fireplace Size Requirements Minimum Fireplace OpeningClearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesHorizontal Venting Vent Information and DiagramsVent Table Key Measuring StandardsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Class a Wood Pipe Inlet AIR Vent Pipe Stainless Steel Placing, Securing and Leveling the Appliance Factory Built Wood Burning Installing Adaptor and Termination CapMasonry Damper Flashing Kit OptionalGas Pressures Gas InformationFuel Conversions Gas Connection High Altitude Installations Electrical Information Wiring the ApplianceON/OFF Switch Appliance RequirementsOptional Accessories Junction Box InstallationInstallation for Fan Optional Fan Wiring Diagram Finishing Mantel ProjectionsAccessories Appliance SetupClean the Appliance Ember PlacementLog Set Assembly LOGS-FB-ZC Positioning the LogsGroove Removing Glass Assembly Glass AssemblyAir Shutter Setting Replacing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance Lighting Appliance Standing Pilot IgnitionAfter Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Frequently Asked Questions Issue SolutionsStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsPart number list on following Log Set AssemblyService Parts At Depot Service Parts ListStocked Valve Assembly Service PartsCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

FB-ZC-S specifications

Hearth and Home Technologies has consistently been at the forefront of innovative heating solutions, and the FB-ZC-S is a prime example of their dedication to quality and performance. This gas fireplace has been designed not only for aesthetic appeal but also for optimal functionality, making it an excellent choice for modern homes.

One of the standout features of the FB-ZC-S is its impressive heating efficiency. Utilizing advanced gas technology, this fireplace ensures a high rate of heat output while maintaining low emissions. Homeowners will appreciate the efficient use of fuel, which translates into cost savings on energy bills. The FB-ZC-S is capable of producing a significant amount of heat, making it suitable for larger spaces.

The design of the FB-ZC-S is another highlight, featuring a sleek, contemporary look that fits well with a variety of interior styles. Its clean lines and minimalist approach allow it to blend seamlessly into any living area while serving as a stunning focal point. The unit comes with a variety of customizable options, including different front styles, decorative media, and trim finishes, enabling homeowners to personalize their fireplace according to their tastes.

Hearth and Home Technologies has equipped the FB-ZC-S with state-of-the-art technologies, including an easy-to-use control system. The intuitive interface allows users to adjust the flame height and heat output with ease, providing the ultimate comfort at their fingertips. Additionally, the fireplace can be integrated with smart home systems, enabling users to control their heating from anywhere, whether via smartphone or voice commands.

Further enhancing its appeal, the FB-ZC-S features a direct vent system that offers safe and efficient operation. This system allows for the expulsion of combustion gases outside the home while drawing in outside air for combustion, thus maintaining indoor air quality. Safety is paramount, and the FB-ZC-S is built with multiple safety features, including automatic shut-off systems and high-temperature safety locks.

In summary, the Hearth and Home Technologies FB-ZC-S is a state-of-the-art gas fireplace that blends modern design with advanced heating technology. Its impressive efficiency, customizable options, user-friendly controls, and safety features make it a standout choice for homeowners looking to enhance their living space with effective and stylish warmth. Whether for cozy family gatherings or serene evenings at home, the FB-ZC-S is designed to provide both comfort and charm.
Top Page Image Contents