Hearth and Home Technologies FB-ZC-S Check Pilot Flame Appearance, After Appliance is Lit

Page 28

C. Check Pilot Flame Appearance

Pilot flame must contact the thermocouple and thermopile for reliable appliance operation.

•Pilot flame should be as shown in Figure 12.1.

Figure 12.1 Proper Pilot Flame

•If adjustment is needed remove cap screw from gas valve using 1/8 inch standard screwdriver (see Figure 12.2).

•Turn adjustment screw clockwise to increase pilot flame size. Make small adjustments.

PILOT

ADJUSTMENT

Figure 12.2 Adjustments

•Do NOT turn adjustment screw counter-clockwise too far as it will come out of the valve allowing gas to escape.

•Replace cap screw and seal to prevent gas leaks.

•Check for gas leaks after tightening.

D. After Appliance is Lit

WARNING

Glass door must be in place when appliance is operating.

Risk of:

•Combustion Fumes

•Fire

Do NOT operate appliance with glass door removed.

•Open viewing glass for servicing only.

•Glass door MUST be in place and sealed before operating appliance.

•Only use glass door certified for use with appliance.

•Glass replacement should be done by qualified technician.

Initial Break-in Procedure

When you light the appliance, you may notice that it pro- duces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process. Condensation of the glass is normal.

Note: The appliance should be run three to four hours on the initial start-up. Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the appliance for an additional 12 hours. This will help to cure the products used in the paint and logs.

During this break-in period it is recommended that some windows in the house be opened for air circulation. This will help avoid setting off smoke detectors, and help eliminate any odors associated with the appliance’s initial burning.

28

Heat & Glo • FB-ZC-S • 2019-910 Rev. G • 11/08

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Model What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Design and Installation Considerations Getting StartedInspect Appliance and Components Tools and Supplies NeededInspect Firebox Fireplace Size Requirements Minimum Fireplace OpeningClearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent Information and Diagrams Vent Table KeyHorizontal Venting Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Class a Wood Pipe Inlet AIR Vent Pipe Stainless Steel Placing, Securing and Leveling the Appliance Installing Adaptor and Termination Cap MasonryFactory Built Wood Burning Damper Flashing Kit OptionalFuel Conversions Gas Connection Gas InformationGas Pressures High Altitude Installations Wiring the Appliance ON/OFF SwitchElectrical Information Appliance RequirementsInstallation for Fan Optional Junction Box InstallationOptional Accessories Fan Wiring Diagram Finishing Mantel ProjectionsAppliance Setup Clean the ApplianceAccessories Ember PlacementLog Set Assembly LOGS-FB-ZC Positioning the LogsGroove Glass Assembly Air Shutter SettingRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsBefore operating this appliance have a qualified technician Lighting Appliance Standing Pilot IgnitionCheck Pilot Flame Appearance Initial Break-in ProcedureAfter Appliance is Lit Frequently Asked Questions Issue SolutionsSymptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsService Parts Log Set AssemblyPart number list on following Stocked Service Parts ListAt Depot Valve Assembly Service PartsCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

FB-ZC-S specifications

Hearth and Home Technologies has consistently been at the forefront of innovative heating solutions, and the FB-ZC-S is a prime example of their dedication to quality and performance. This gas fireplace has been designed not only for aesthetic appeal but also for optimal functionality, making it an excellent choice for modern homes.

One of the standout features of the FB-ZC-S is its impressive heating efficiency. Utilizing advanced gas technology, this fireplace ensures a high rate of heat output while maintaining low emissions. Homeowners will appreciate the efficient use of fuel, which translates into cost savings on energy bills. The FB-ZC-S is capable of producing a significant amount of heat, making it suitable for larger spaces.

The design of the FB-ZC-S is another highlight, featuring a sleek, contemporary look that fits well with a variety of interior styles. Its clean lines and minimalist approach allow it to blend seamlessly into any living area while serving as a stunning focal point. The unit comes with a variety of customizable options, including different front styles, decorative media, and trim finishes, enabling homeowners to personalize their fireplace according to their tastes.

Hearth and Home Technologies has equipped the FB-ZC-S with state-of-the-art technologies, including an easy-to-use control system. The intuitive interface allows users to adjust the flame height and heat output with ease, providing the ultimate comfort at their fingertips. Additionally, the fireplace can be integrated with smart home systems, enabling users to control their heating from anywhere, whether via smartphone or voice commands.

Further enhancing its appeal, the FB-ZC-S features a direct vent system that offers safe and efficient operation. This system allows for the expulsion of combustion gases outside the home while drawing in outside air for combustion, thus maintaining indoor air quality. Safety is paramount, and the FB-ZC-S is built with multiple safety features, including automatic shut-off systems and high-temperature safety locks.

In summary, the Hearth and Home Technologies FB-ZC-S is a state-of-the-art gas fireplace that blends modern design with advanced heating technology. Its impressive efficiency, customizable options, user-friendly controls, and safety features make it a standout choice for homeowners looking to enhance their living space with effective and stylish warmth. Whether for cozy family gatherings or serene evenings at home, the FB-ZC-S is designed to provide both comfort and charm.
Top Page Image Contents