Hearth and Home Technologies EM-415H Ft min. from top of uppermost chimney section to air inlet

Page 14

3 ft min. from top of uppermost chimney section to air inlet.

Figure 4.2 Outside Air Inlet Locations

Attic insulation shield may be used to keep insulation away from chimney.

Ceiling firestop on floor of attic.

Handle left - open

Handle right - closed

Figure 4.4 Locating the Outside Air Control

NO

NO

 

Garage or

NO

Outlet blocked by

combustible

snow, leaves, etc.

liquids storage

Attic space

NO

Outlet placed

higher than 3 ft

below the

termination cap

YES

Factory-built

Clear area

fireplace

outside

 

house or in

 

ventilated

 

crawl space

Use only duct materials specified

 

by manufacturer (preferably with

 

short run or mainly straight duct,

 

except small dip for cold air trap

 

which will help prevent flow of cold air).

Figure 4.3 Outside Combustion Air Placement

14

Heat & Glo • EM-415/EM-415H • 31317 Rev Q • 10/06

Image 14
Contents Models EM-415 EM-415H Woodburning Fireplace Fire RiskNumber Listing Label Information/LocationGrate Table of Contents Not intended for use as a primary heat source Listing and Code ApprovalsAppliance Certification Negative Pressure Design and Installation ConsiderationsGetting Started Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemFire Risk Explosion Risk Tools and Supplies NeededInspect Fireplace and Components Framing and Clearances Selecting Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the Fireplace¨E. Construct the Chase Chimney RequirementsFire Risk Sharp Edges Asphyxiation Risk Installation of FireplaceInstall the Outside Air Kit Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Place the Protective Metal Hearth Strips Secure the FireplacePosition the Fireplace Level the FireplaceChimney Assembly Height of Chimney Components Using Offsets/Returns Degree SL306 SL312 SL318 SL324 SL336 SL348Install the Ceiling Firestops Assemble the Chimney SectionsSecure the Chimney Install the Attic Insulation ShieldDouble-check the Chimney Assembly Complete the Enclosure Chimney TerminationChase Top Install the Termination CapInstall the Chimney Air Kit required in Canada Installing an ST375 Square Termination Cap Gas Log/Lighter Provisions AccessoriesJunction Box Installation Gas Code, Ansi Z223.1Installation of Fan Shock RiskFinishing Hearth ExtensionGlass Doors Finishing MaterialMantel Combustible MaterialOperating Instructions General InformationFlue Damper Outside AirClear Space Near the Fireplace FirescreenFirewood GrateWood Fuel MoistureStarting a Fire Troubleshooting Understanding Vent ProblemsSolutions Diagnostics and Problem SolvingDiagnostic Questions Can’t get a good fire going. What am I doing wrong?fireplace burns the wood too fast. What can I do? Disposal of Ashes Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Firebox RefractoryClean Maintenance Task ListWhen cleaning glass door Chimney FireFireplace Dimensions Reference Materials¨ B. Fireplace Components Catalog # DescriptionChimney Components Catalog #14-1/2 1829 mm 10-7/8 276 mm 406 mm 508 mm TR442 TR442 / 444 TV Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XMinimum Base Dimensions 26.5 X 28 with 34 X 34 with 20 xService Parts EM-415 SeriesDescription of Part EM-415 EM-415H Qty Herringbone Brick Refractory option available week 03/04This page intentionally left blank Warranty For Heat & GLO Fireplaces Limited WarrantyContact Information