Hearth and Home Technologies EM-415H owner manual Typical Fireplace System

Page 7

C. Typical Fireplace System

 

The Heat & Glo fireplace system consists of the following:

 

Note:Junction box should be installed during

Fireplace/integral grate/refractory/outside air system

initial setup to avoid major reconstruction.

Chimney termination cap

 

 

Chimney system

 

Hearth extension

 

Optional components include:

Glass doors

Chimney air kit

Fan kit

Additional lateral

support for chimneyTermination cap above roof (or enclosed

in chase) if needed

Non-combustible

 

roof flashing maintains

Storm Collar

minimum clearance

around chimney

 

 

Chimney penetrates roof

 

preferably without affecting

Support straps

roof rafters

 

on rafter supports

 

chimney (not shown)

Offset/Return (with hanger straps)

 

 

Attic insulation shield (not shown) must

Ceiling firestop

be used here to keep insulation away

from chimney if attic is insulated

on floor of attic

 

Chimney system

Framing headed off

 

Combustible

in ceiling joists

 

framing/header

Enclosed space above

on top of

and around fireplace

V-shaped

 

standoffs

 

(spacers)

Mantel and surround

 

Decorative facing

 

and trim

Hearth extension

Outside combustion air

Factory-built fireplace

Protective metal hearth strip(s)

Figure 2.2 Typical Fireplace System

Heat & Glo • EM-415/EM-415H • 31317 Rev Q • 10/06

7

Image 7
Contents Fire Risk Models EM-415 EM-415H Woodburning FireplaceGrate Listing Label Information/LocationNumber Table of Contents Appliance Certification Listing and Code ApprovalsNot intended for use as a primary heat source Asphyxiation Risk Design and Installation ConsiderationsGetting Started Negative PressureMarginal Location Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements ¨E. Construct the ChaseRisk of Smoke Spillage Installation of FireplaceInstall the Outside Air Kit Fire Risk Sharp Edges Asphyxiation RiskFt min. from top of uppermost chimney section to air inlet Level the Fireplace Secure the FireplacePosition the Fireplace Place the Protective Metal Hearth StripsChimney Assembly Height of Chimney Components Degree SL306 SL312 SL318 SL324 SL336 SL348 Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsDouble-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney Chimney Termination Complete the EnclosureInstall the Chimney Air Kit required in Canada Install the Termination CapChase Top Installing an ST375 Square Termination Cap Gas Code, Ansi Z223.1 AccessoriesJunction Box Installation Gas Log/Lighter ProvisionsShock Risk Installation of FanHearth Extension FinishingCombustible Material Finishing MaterialMantel Glass DoorsGeneral Information Operating InstructionsFirescreen Outside AirClear Space Near the Fireplace Flue DamperMoisture GrateWood Fuel FirewoodStarting a Fire Understanding Vent Problems TroubleshootingCan’t get a good fire going. What am I doing wrong? Diagnostics and Problem SolvingDiagnostic Questions Solutionsfireplace burns the wood too fast. What can I do? Firebox Refractory Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Disposal of AshesChimney Fire Maintenance Task ListWhen cleaning glass door CleanReference Materials Fireplace DimensionsCatalog # Description ¨ B. Fireplace ComponentsCatalog # Chimney Components14-1/2 1829 mm 10-7/8 276 mm 406 mm 508 mm 20 x Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XMinimum Base Dimensions 26.5 X 28 with 34 X 34 with TR442 TR442 / 444 TVEM-415 Series Service PartsHerringbone Brick Refractory option available week 03/04 Description of Part EM-415 EM-415H QtyThis page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesContact Information