Hearth and Home Technologies BIR42 owner manual 15-1/4 387 mm

Page 52

			Inside
			Diameter
			11 in.
			(279 mm)
	21 in.		Outside
	(533 mm)		Outside
	(533 mm)		Diameter
			Diameter
			13 in.
			(330 mm)
		SL1130 Offset/Return

Assembled

Diameter: 17 in./432 mm

Height: 24 in./610 mm

AS10 Straight Attic Insulation Shield

13 in.	2 in.
(330 mm)

(51 mm)

JB577 Chimney Joint Band

13 in. (330 mm)

CB576 Chimney Joint Band

A

B17 in. (432 mm)

Catalog #	A		B
FS538	0-deg.	17 in.		432 mm
FS540	30-deg.	26 in.		660 mm

15-1/4 in.

(387 mm)

29 in.	25-1/4 in.
(737 mm)	(641 mm)

RF570 Roof Flashing

15-1/4in.

(387 mm)

	39-7/8 in.	28 in.
	39-7/8 in.	(711 mm)
	(1013 mm)	(711 mm)
	(1013 mm)
	RF571 Roof Flashing

52	Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08

Image 52

Contents Hot screen/mesh and glass doors will cause burns Fire RiskGrate Listing Label Information/LocationNumber Table of Contents Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeatilator Birmingham BIR42 4059-308 F 11/08 Listing and Code Approvals Appliance CertiﬁcationNon-Combustible Materials Combustible MaterialsOperating Instructions Your FireplaceSeasoned Wood Starting a FireGrate FirescreenGlass Doors Vented Gas Log Sets & Gas Log LightersOptional Components Clear SpaceWood Fuel Hardwood vs SoftwoodChimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Glass Cleaning Check Firebox Molded Brick PanelInspect Grate Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating your Fireplace & Chimney Recommended Chimney LocationsInspect Fireplace and Components Tools and Supplies NeededTypical Fireplace Components Framing & Clearances Select Fireplace LocationClearances Air Space ClearancesSidewalls/Surrounds Frame the FireplaceInstallation of Fireplace Things to ConsiderPosition the Fireplace Place Protective Metal Hearth StripsYES Install Outside Air Kit Outside Air InstallationChimney Assembly Chimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleAssemble Chimney Sections Assembling Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield Prepare Attic Insulation ShieldInstall Flashing Complete InstallationCut Out Hole in Roof Chimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST1175 Square Termination CapTCT1175 Terra Cotta Cap Radiation Shield ShroudsField Constructed Shrouds Mailbox Style Shroud radiation shield required Installation of Molded Brick Panel Install Hearth Molded Brick PanelInstall Side Molded Brick Panel/Traditional Install Back Molded Brick Panel/TraditionalInstall Side Molded Brick Panel Herring- bone Install Back Molded Brick Panel Herring- boneInstall Mortar Install ScreensHearth Extension Finishing= 1/k x inches of thickness Noncombustible Framing MaterialEquivalent insulation Finishing MaterialsNon-combustible Sealant Finishing Material Noncombustible FacingCombustible Mantel Mantel, Adding Extra Support 14 Secure to FramingBrick Front Accessories Gas Log/Lighter ProvisionWood Burning Inserts Gas Code, Ansi Z223.1Fireplace Dimensions Reference MaterialsID6 Insulated Duct .4 mm i.d 1067 mm UD6 Uninsulated Duct Chimney Components Catalog #15-1/4 387 mm 31-3/4 806 mm 34-5/8 879 mm CT56 Chase Top Service PartsContact Information