Hearth and Home Technologies Grand-XTS, Supreme-XTS Placing, Securing and Leveling the Appliance

Page 12

CUT AND BEND

FLASHING AS NEEDED

TO FIT CHIMNEY

SEALANT

ADHESIVE

Figure 7.2

•Trim chimney top plate to minimize excess overhang or bend over flue tile (see Figure 7.2).

•Place 3/8 inch bead of 300º F silicone on flue tile top.

C.Placing, Securing and Leveling the Appliance

•Install insert (without surround attached) into existing fireplace while pulling collar slide plate forward.

•Install gas line into hole provided on insert side.

•If applicable install remote control wires into insert side (see Section 6, F.).

•Secure collar slide plate to appliance by placing locking handle into position with locking tabs (see Figure 7.1) and secure with #8 screw.

•Level the appliance from side to side and front to back. If necessary, use the leveling legs included with the manual bag to set each corner of the base.

•Position any excess flexible vent pipe back up into chimney without sagging. Twist and push flex vent together to shorten.

•Non-combustible, unfaced fiberglass insulation may be installed between the back of the decorative surround and the face of the existing fireplace surround to which the insert is being installed. This insulation is not required, but can assist in the prevention of infiltration of cold air and odors from the chimney.

•Attach surround. Follow instructions accompanying surround.

•Push insert so that surround becomes tight against face of fireplace.

WARNING

Fire Risk.

Only an approved Hearth & Home Technologies surround may be used to cover integral grills on solid fuel burning fireplaces.

• No other components such as shrouds, sheet- metal plates, etc., may be used to seal off vents.

WARNING

Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

WARNING

Explosion Risk.

Combustion Fume Risk.

•Connect vent sections per installation instructions.

•The 3 foot section of stainless steel flexible pipe MUST be attached directly to the exhaust collar on the collar slide plate.

•Connect exhaust vent pipe ONLY to exhaust starting collar and termination cap center collar.

•Connect inlet air vent ONLY to inlet air collar on appliance and either the termination cap inlet air collar OR terminate within chimney.

•Do NOT allow vent to sag below connection point to appliance.

12

Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev. G • 9/08

 

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Models Supreme-XTS Grand-XTS What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Design and Installation Considerations Getting StartedTools and Supplies Needed Inspect Appliance and ComponentsFireplace Size Requirements Minimum Fireplace OpeningClearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent Information and Diagrams Vent Table KeyHorizontal Venting Measuring StandardsInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVenting Components Placing, Securing and Leveling the Appliance Installing Adaptor and Termination Cap Factory Built Wood BurningDamper Flashing Kit Optional Gas Information Fuel Conversions Gas ConnectionGas Pressures High Altitude Installations Wiring the Appliance ON/OFF SwitchElectrical Information Appliance RequirementsJunction Box Installation Optional AccessoriesFAN Junction BOX Finishing Mantel ProjectionsAppliance Setup Clean the ApplianceAccessories Ember PlacementLog Set Assembly LOGS-SXT Positioning the LogsHeat & Glo Supreme-XTS, Grand-XTS 349-901 Rev. G 9/08 Heat & Glo Supreme-XTS, Grand-XTS 349-901 Rev. G 9/08 Log Set Assembly LOGS-GXT Heat & Glo Supreme-XTS, Grand-XTS 349-901 Rev. G 9/08 Heat & Glo Supreme-XTS, Grand-XTS 349-901 Rev. G 9/08 Glass Assembly Air Shutter SettingOperating Instructions Before Lighting ApplianceBefore operating this appliance have a qualified technician Lighting Appliance Standing Pilot IgnitionInitial Break-in Procedure Check Pilot Flame AppearanceAfter Appliance is Lit Frequently Asked Questions Issue SolutionsTroubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsLog Set Assembly Service PartsPart number list on following SUPREME-XTS At DepotGRAND-XTS Service Parts LOGS-GXTStanding Pilot Valve Assembly StockedCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

Supreme-XTS, Grand-XTS specifications

Hearth and Home Technologies (HHT) has consistently set the bar in the realm of modern heating solutions, and their Grand-XTS and Supreme-XTS models exemplify this commitment to innovation and quality. These sleek and stylish gas fireplaces are designed not only to provide warmth but also to enhance the aesthetic of any living space.

The Grand-XTS model features a stunning design that can be customized to fit various interior styles. With an expansive viewing area, it allows for an impressive flame presentation that creates a cozy ambiance. The inclusion of MaxHeat technology ensures optimal heat output, making it an efficient choice for heating larger areas without sacrificing style. This model is equipped with a powerful fan system that circulates warm air throughout the room quickly, enhancing the overall comfort of your living space.

Meanwhile, the Supreme-XTS takes luxury to the next level with additional modern features. Designed for elegance, it comes with a range of decorative options, including various media beds and reflective panels that amplify the fire's glow. The fireplace's Intellifire Ignition System offers a convenient and reliable startup, ensuring that users can enjoy their fireplace with minimal hassle. Furthermore, the Supreme-XTS integrates seamlessly with smart home systems, allowing for remote operation and personalized settings directly from your smartphone.

Both models offer customizable options, including adjustable flame heights and temperature settings. This versatility lets homeowners create their desired atmosphere, whether for a warm, welcoming gathering or a more intimate setting. The advanced safety features incorporated into both models, such as automatic shut-off systems and glass safety screens, provide peace of mind while allowing for an unparalleled heating experience.

The Grand-XTS and Supreme-XTS by Hearth and Home Technologies not only prioritize efficiency and safety but also cater to individual tastes with a selection of finishes and trim options. With their superior performance, elegant aesthetics, and advanced technology, these fireplaces stand out as a premier choice for those looking to enhance both comfort and visual appeal in their homes. Whether you choose the Grand-XTS for its expansive heat capabilities or the Supreme-XTS for its luxurious features, either model will transform your living space into a haven of warmth and style.
Top Page Image Contents