Hearth and Home Technologies RUTHERFORD-42 owner manual TCT1175 Terra Cotta Cap

Page 35

•TCT1175 Terra Cotta Cap

Collar

2 in. (51 mm)

Minimum Height

Chase Top

Place waterproof sealer under each flange of the termina- tion cap and on top of each screw to help prevent leaks.

Termination Cap

The last section of pipe must stop between 2 in. (51 mm) above top of chase and 7 in. (178 mm) below top of chase

2 in. (51 mm)

7 in. (178 mm)

Chase

Chimney

Pipe

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)

Figure 9.7 Installing a TCT1175 Terra Cotta Cap

Heat & Glo • RUTHERFORD-42 • 4059-309 Rev G • 11/08

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents
Fire Risk Hot screen/mesh and glass doors will cause burnsNumber Listing Label Information/LocationGrate Table of Contents CONDITIONS, Exclusions & Limitation of Liability ÎWarranty Hearth & Home Technologies Limited WarrantyHeat & Glo RUTHERFORD-42 4059-309 Rev G 11/08 Combustible Materials Listing and Code ApprovalsAppliance Certification Non-Combustible MaterialsYour Fireplace Operating InstructionsFirescreen Seasoned WoodStarting a Fire GrateClear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional ComponentsHardwood vs Softwood Wood FuelDisposal of Ashes Maintainance and ServiceChimney Inspection/Cleaning Frequency As desired Glass CleaningCheck Firebox Molded Brick Panel Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedNegative Pressure Design and Installation ConsiderationsDraft Recommended Chimney Locations Locating your Fireplace & ChimneyTypical Fireplace Components Tools and Supplies NeededInspect Fireplace and Components Select Fireplace Location Framing & ClearancesAir Space Clearances ClearancesFrame the Fireplace Sidewalls/SurroundsPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceYES Outside Air Installation Install Outside Air KitChimney Assembly Height of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssembling Chimney Sections Assemble Chimney SectionsInstalling the Ceiling Firestop Install Ceiling FirestopsPrepare Attic Insulation Shield Install Attic Insulation ShieldCut Out Hole in Roof Complete InstallationInstall Flashing Flat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST1175 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Field Constructed Shrouds ShroudsRadiation Shield Mailbox Style Shroud radiation shield required Install Back Molded Brick Panel-Traditional Installation of Molded Brick PanelInstall Hearth Molded Brick Panel Install Side Molded Brick Panel-TraditionalInstalling Back Molded Brick Panel-Her- ringbone Installing Side Molded Brick Panel-Herring- boneInstall Screens Install Mortar= 1/k x inches of thickness FinishingHearth Extension Finishing Materials NoncombustibleFraming Material Equivalent insulationNon-combustible Sealant Noncombustible Facing Finishing MaterialCombustible Mantel 14 Secure to Framing Mantel, Adding Extra SupportBrick Front Gas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provision Wood Burning InsertsReference Materials Fireplace DimensionsID6 Insulated Duct .4 mm i.d 1067 mm UD6 Uninsulated Duct Catalog # Chimney Components15-1/4 387 mm 31-3/4 806 mm 34-5/8 879 mm CT56 Chase Top Parts ServiceDo not Discard this Manual
Top Page Image Contents