Hearth and Home Technologies RUTHERFORD-42 owner manual Yes

Page 22

3 ft min. from top of uppermost chimney section to air inlet.

Outside air installed on both sides (right side not shown)

Figure 7.3 Outside Air Inlet Locations

	NO	NO
	NO	Garage or	NO
	Outlet blocked by	combustible	NO
	snow, leaves, etc.	liquids storage	Attic space
			NO
			Outlet placed
			higher than 3 ft
			below the
			termination cap
	YES	Factory-built
	Clear area	Factory-built
	Clear area	fireplace
	outside	fireplace
	outside
	house or in
	ventilated
	crawl space
	Figure 7.4 Outside Air Placement
	22	Heat & Glo • RUTHERFORD-42 • 4059-309 Rev G • 11/08

Image 22

Contents

Hot screen/mesh and glass doors will cause burns Fire RiskGrate Listing Label Information/LocationNumber Table of Contents ÎWarranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeat & Glo RUTHERFORD-42 4059-309 Rev G 11/08 Non-Combustible Materials Listing and Code ApprovalsAppliance Certiﬁcation Combustible MaterialsOperating Instructions Your FireplaceGrate Seasoned WoodStarting a Fire FirescreenOptional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear SpaceWood Fuel Hardwood vs SoftwoodChimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Inspect Grate Glass CleaningCheck Firebox Molded Brick Panel Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating your Fireplace & Chimney Recommended Chimney LocationsInspect Fireplace and Components Tools and Supplies NeededTypical Fireplace Components Framing & Clearances Select Fireplace LocationClearances Air Space ClearancesSidewalls/Surrounds Frame the FireplacePosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsYES Install Outside Air Kit Outside Air InstallationChimney Assembly Chimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleAssemble Chimney Sections Assembling Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield Prepare Attic Insulation ShieldInstall Flashing Complete InstallationCut Out Hole in Roof Chimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST1175 Square Termination CapTCT1175 Terra Cotta Cap Radiation Shield ShroudsField Constructed Shrouds Mailbox Style Shroud radiation shield required Install Side Molded Brick Panel-Traditional Installation of Molded Brick PanelInstall Hearth Molded Brick Panel Install Back Molded Brick Panel-TraditionalInstalling Side Molded Brick Panel-Herring- bone Installing Back Molded Brick Panel-Her- ringboneInstall Mortar Install ScreensHearth Extension Finishing= 1/k x inches of thickness Equivalent insulation NoncombustibleFraming Material Finishing MaterialsNon-combustible Sealant Finishing Material Noncombustible FacingCombustible Mantel Mantel, Adding Extra Support 14 Secure to FramingBrick Front Wood Burning Inserts AccessoriesGas Log/Lighter Provision Gas Code, Ansi Z223.1Fireplace Dimensions Reference MaterialsID6 Insulated Duct .4 mm i.d 1067 mm UD6 Uninsulated Duct Chimney Components Catalog #15-1/4 387 mm 31-3/4 806 mm 34-5/8 879 mm CT56 Chase Top Service PartsDo not Discard this Manual