Hearth and Home Technologies RUTHERFORD-42 owner manual Installation of Molded Brick Panel

Page 38

11 Installation of Molded Brick Panel

A. Install Hearth Molded Brick Panel

•Place hearth panel into the fireplace.

B. Install Side Molded Brick Panel-Traditional

•If a gas line is to be installed, remove the knockouts in the inner firebox and in the outer shell on the side of your choice. Refer to dimension drawings for location of knockouts and Section 13.A. for gas provisions.

•Do NOT remove screen rods.

•Refer to Figure 11.1.

•Install lower side panel, tapered edge to the front. Align the front edge with the front of the column (or butted to the surround if installed).

•Install two T-brackets stem down into mortar line, do not tighten.

•Install upper side panel in the unit, tapered edge to the front. Position the bottom of panel behind the T-brackets. Install two T-brackets stem up into mortar lines, one on its side on the front edge, do not tighten.

•Install two Z-brackets in the mortar joints across the top. Tighten these and all previously installed brackets.

•Install second side panel following the steps above.

Note: Use T-brackets as templates and drill pilot holes into the inner shell with the drill bit provided. Side panels must be installed first.

C. Install Back Molded Brick Panel-Traditional

•Refer to Figure 11.1.

•Set the grate brackets in place, 26.5 in. (673 mm) center to center.

•Install the lower back panel. Center from side to side.

•Install three T-brackets stem down into mortar line to hold lower back in position. Do not tighten.

•Install upper back panel. Position bottom of panel behind the previously installed T-brackets. Install two T-brackets stem side up into mortar line, do not tighten

•Install two Z-brackets in the mortar joints across the top. Tighten these and all previously installed brackets.

Front

 

 

Upper Back

Upper Side

Molded Brick Panel

Molded Brick Panel

 

 

Right Side

 

Molded Brick Panel

 

removed for

 

clarity

Lower Side

Lower Back

Molded Brick Panel

Molded Brick Panel

 

 

Hearth Molded Brick Panel

Figure 11.1 Traditional Molded Brick Panel

38

Heat & Glo • RUTHERFORD-42 • 4059-309 Rev G • 11/08

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Hot screen/mesh and glass doors will cause burns Fire RiskNumber Listing Label Information/LocationGrate Table of Contents ÎWarranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeat & Glo RUTHERFORD-42 4059-309 Rev G 11/08 Non-Combustible Materials Listing and Code ApprovalsAppliance Certification Combustible MaterialsOperating Instructions Your FireplaceGrate Seasoned WoodStarting a Fire FirescreenOptional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear SpaceWood Fuel Hardwood vs SoftwoodDisposal of Ashes Maintainance and ServiceChimney Inspection/Cleaning Inspect Grate Glass CleaningCheck Firebox Molded Brick Panel Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemNegative Pressure Design and Installation ConsiderationsDraft Locating your Fireplace & Chimney Recommended Chimney LocationsTypical Fireplace Components Tools and Supplies NeededInspect Fireplace and Components Framing & Clearances Select Fireplace LocationClearances Air Space ClearancesSidewalls/Surrounds Frame the FireplacePosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsYES Install Outside Air Kit Outside Air InstallationChimney Assembly Chimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleAssemble Chimney Sections Assembling Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield Prepare Attic Insulation ShieldCut Out Hole in Roof Complete InstallationInstall Flashing Chimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST1175 Square Termination CapTCT1175 Terra Cotta Cap Field Constructed Shrouds ShroudsRadiation Shield Mailbox Style Shroud radiation shield required Install Side Molded Brick Panel-Traditional Installation of Molded Brick PanelInstall Hearth Molded Brick Panel Install Back Molded Brick Panel-TraditionalInstalling Side Molded Brick Panel-Herring- bone Installing Back Molded Brick Panel-Her- ringboneInstall Mortar Install Screens= 1/k x inches of thickness FinishingHearth Extension Equivalent insulation NoncombustibleFraming Material Finishing MaterialsNon-combustible Sealant Finishing Material Noncombustible FacingCombustible Mantel Mantel, Adding Extra Support 14 Secure to FramingBrick Front Wood Burning Inserts AccessoriesGas Log/Lighter Provision Gas Code, Ansi Z223.1Fireplace Dimensions Reference MaterialsID6 Insulated Duct .4 mm i.d 1067 mm UD6 Uninsulated Duct Chimney Components Catalog #15-1/4 387 mm 31-3/4 806 mm 34-5/8 879 mm CT56 Chase Top Service PartsDo not Discard this Manual

RUTHERFORD-42 specifications

Hearth and Home Technologies presents the RUTHERFORD-42, an exceptional gas fireplace that combines sophisticated design with advanced functionality. This model signifies the perfect blend of aesthetics and performance, making it a favored choice for homeowners seeking to enhance their living spaces with the warmth and comfort of a fireplace.

One of the primary features of the RUTHERFORD-42 is its impressive viewing area, measuring 42 inches wide. This expansive glassfront design offers a stunning visual display of the flames, creating a cozy ambiance that enhances any room. The fireplace is framed with a stylish surround that can be customized to match various interior styles, adding a touch of elegance to contemporary and traditional homes alike.

Equipped with advanced technology, the RUTHERFORD-42 ensures efficient heat output while maintaining ease of use. The fireplace features an electronic ignition system that provides reliability and convenience with a simple push-button start. Additionally, it incorporates a thermostat remote control, allowing users to easily regulate the temperature from anywhere in the room. This functionality not only enhances user comfort but also improves energy efficiency.

The unit is designed with a powerful yet quiet fan that circulates warm air throughout the space, ensuring even heat distribution. This makes the RUTHERFORD-42 an excellent option for supplemental heating in larger rooms, providing both style and warmth during colder months.

Safety is a paramount concern in all Hearth and Home Technologies products, and the RUTHERFORD-42 is no exception. It includes safety screens that protect against accidental contact with the flames, ensuring peace of mind while enjoying the fire’s warmth. Furthermore, it complies with stringent safety standards, making it a reliable choice for families.

In terms of aesthetics, the RUTHERFORD-42 offers various media options, including glass, ceramic logs, and stone, allowing homeowners to personalize the fire's appearance to align with their home’s décor. The fireplace is also available in different finishes, giving users the flexibility to create a focal point that perfectly complements their interior design.

Overall, the Hearth and Home Technologies RUTHERFORD-42 is a standout model that combines cutting-edge technology, safety features, and design flexibility, making it an excellent choice for anyone looking to add a stylish and functional gas fireplace to their home.
Top Page Image Contents